Re: [Chrysler300] 300F problems Pertronix
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] 300F problems Pertronix



Sorry, error in last e-mail.

MSD CDI ignition! 6A Box (Not Mallory)



From: Tony Rinaldi <awrdoc@xxxxxxxxx>
Date: Fri, 16 Mar 2007 10:42:51 -0400
To: Richard Osborne <richard@xxxxxxxxxxxx>, John Hertog
<crossram@xxxxxxxxxxxxx>, VICTOR KOONTZ <wikki123@xxxxxxxxxxxxx>, Chrysler
300 Club <chrysler300@xxxxxxxxxxxxxxx>
Conversation: [Chrysler300] 300F problems Pertronix
Subject: Re: [Chrysler300] 300F problems Pertronix

 
 
 

To All,

You all must be careful when sharing war stories about the Pertronix unit.

Are you talking about the original one or the (improved?) Pertronix II, the
upgraded model.

John  Hertog put the original Pertronix unit in my ³F² and the car ran
horribly. He had my distributor re set up with dual points (calibrated by
Don Verity) and the car ran well.

If you take the switched power source from the ballast resistor, be sure to
take it from the origin (before the resistor 12V side) and not after the
resistor (6V side).

Subsequently, I converted my car to Mallory CDI ignition with the points
acting only as signaling devices. Had to redo wires with epoxy Mallory coil.

Tony

From: Richard Osborne <richard@xxxxxxxxxxxx <mailto:richard%40zippynet.com>
>
Date: Fri, 16 Mar 2007 05:44:22 -0500
To: "John J. Hertog" <crossram@xxxxxxxxxxxxx
<mailto:crossram%40optonline.net> >, 'VICTOR KOONTZ'
<wikki123@xxxxxxxxxxxxx <mailto:wikki123%40sbcglobal.net> >,
<chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300%40yahoogroups.com> >
Subject: Re: [Chrysler300] 300F problems Pertronix

John,

I think something else is the issue here. There is NO dwell setting with the
Pertronix upgrade. It is the absolute  definition of plug and play. I added
this to the white G last year. I had accidentally pulled some of the wires
loose from the points while attempting a re-detail of the distributor.
Rather than screw with setting the points back up, I called John Lazenby and
ordered the Pertronix.

The hardest part of the install was finding a good non-obvious power source.
I suspect this is where the problem at hand lies. I no longer have the
instructions, but it is very specific the power requirements. I spliced in
around the ballast resistor, I'd have to look at which side, I can't
remember right now.

Once I had it installed, I was amazed as my car was no longer a turd, it
performed great! The car had always run o.k., it just never had any balls. I
feel it now has the power it should have had all along now. I do not mean to
imply that this improvement is strictly because of the Pertronix (I think
something was set incorrectly with the points), but I am very happy with it
and have no interest in switching back to points as I plan  to continue
driving it a lot.

Best regards,

Richard Osborne
 
>>> "John J. Hertog" <crossram@xxxxxxxxxxxxx <mailto:crossram%40optonline.net>
<mailto:crossram%40optonline.net> >
03/15/07 11:07 pm >>>
Hi Victor,  

Welcome to the Club and to the listserver.  For the rest of the group,
Victor owns a 300F hardtop restored by Tom Cox and then owned for a bit by
Thomas Powers.   Very nice black hardtop.  Now on to your question -  and a
good question it is!   I noticed the same dwell readings (I kind of tend to
remember a lower number, though -  like 18 degrees) when I installed a
Pertronix on one or two of my 413 ram cars. And all I can say is that the
car(s) never ran quite right with Pertronix.  I ended up removing them,
reinstalling the factory dual points, and everything was much better again.
Also, what brand and model plug are you using? Comments, anyone?

Vic, you may want to talk to Don Verity, at d.verity@xxxxxxx
<mailto:d.verity%40cox.net>
<mailto:d.verity%40cox.net>   ; he's got a
Sun distributor machine all set up and could fix up your distributor to
spec. and bench- test it ...

Original tires were 9.00-  14 Goodyear BlueStreak w. 2 1/2" whitewalls

John Hertog
Sag Harbor NY

----- Original Message-----
From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>
<mailto:Chrysler300%40yahoogroups.com>
[mailto:Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>
<mailto:Chrysler300%40yahoogroups.com> ]
On
Behalf Of VICTOR KOONTZ
Sent: Thursday, March 15, 2007 5:23 PM
To: chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300%40yahoogroups.com>
<mailto:chrysler300%40yahoogroups.com>
Subject: [Chrysler300] (unknown)

I just got a 300F & the old owner said he had troublewith the car carboning
the plugs within 3 to 4 weeks after replacing the plugs. I haven't had it
long enough to experience that problem, but with the plugs so hard to remove
etc. I don't want go through it. I did replace the plugs when I got the car
because it wouldn't run. The car has a pertronix replacement of the dual
points with a regular coil. I took a dwell reading & it was 22 degrees.
Single points should read 27to34 degrees. Could this cause the fouling  do
to low saturation time ? Should I put in a pertronix high voltage coil ?

[Non-text portions of this message have been removed]

 
    



[Non-text portions of this message have been removed]



------------------------ Yahoo! Groups Sponsor --------------------~--> 
See what's inside the new Yahoo! Groups email.
http://us.click.yahoo.com/0It09A/bOaOAA/yQLSAA/8LmulB/TM
--------------------------------------------------------------------~-> 

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.