Re: [Chrysler300] Radial Tires on Original Bias Ply Wheels
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Radial Tires on Original Bias Ply Wheels



Hi to all,

As promised, I am attaching the text from an article in Old Cars Weekly.
Please do not kill the messenger!

Tony Rinaldi

_______________________________________________________________

The following is reprinted from Old Cars Weekly from Sept 21, 2006 and warns
of the danger of wheel failure unless the rims are replaced by stronger ones
designed for use with radial tires.
_______________________________________________________________
 
Q. Recently, I purchased five new wide whitewall radials from a reputable
tire company (one of your advertisers). The car for their intended use is a
1956 Mercury that previously had bias‑ply tires. Although I had the new
radials professionally mounted and balanced, the front hubcaps come off
while driving, especially the left front on right turns. Can you advise me
if I need to replace the wheel rims with a heavier type? Robert W. Blume,
Sr., Calverton, N.Y.
 
A. Back in 2003, we had a lively discussion of wheels intended for bias‑ply
tires "throwing" hubcaps when mounted with radials. Here are readers'
comments from that discussion. "The problem of cars 'throwing hubcaps' is
much more serious than rim flex and lost hubcaps. Try losing your life with
this problem! Rims for bias-ply tires, radial-ply tires, even disc brake
rims are made out of different alloys. Rims for bias-ply tires cannot use
radials, and bias and simple radial-ply rims cannot be used for disc brakes..
The forces exerted by bias-ply versus radial-ply tires (as well as disc
brakes) are different and need rims made specific to each application. When
using radial tires on bias-ply rims, the rims over‑flex as they are unable
to handle the forces of the radial tires. This over-flexing also means metal
fatigue, breakage (most commonly rim bead edge separation), and deadly
accidents. Many will disagree, touting their successful usage of radial
tires on bias-ply rims, but as a fatal accident investigator, the first
place I looked in any older car accident was at the rims. My advice when
replacing bias tires with radials is to immediately change the rims. One can
tell bias, radial, and disc brake rims by their markings," wrote Sam Egan,
general manager, Automotive Information Clearinghouse, La Mesa, Calif.
Another reader wrote, "When you install a radial tire on an old rim and the
footprint of the tire is wider or equal to the rim bead, the twisting of the
sidewall puts undue stress on the lighter and original rim. We put radial
tires on our 1956 Ford and had the same problem. We cured the problem when
we switched to 1966 Ford rims, which are one inch wider and eight to nine
pounds heavier, which makes them stronger than the old rims." Paul Haase of
Waterloo, Iowa, also advised replacing the rims. "Then if the wheel discs
still slip, they can be held in place a bead of silicone." Sanford Danziger
recommended locating a set of alloy rims, which would obviate the hubcap
problem. To hold the wheel covers in place, assuming movement is still a
problem with the correct rims, Dan Reed says he secured the wheel covers for
his 1956 Cadillac with a strap that was secured by one of the lugnuts. He
found this idea on a 1958 Oldsmobile. The strap has to be long enough to
allow access to the lug nuts. "It won't prevent the wheel cover from coming
off, but will keep it from being lost," he wrote. Marilyn Robinson ended the
problem of wheel covers flying off their Plymouth Valiant by switching to
hubcaps. Terry Wallace of Pensacola, Fla., brushed some of the grit coating
used on surf and skateboards onto the rim area that the wheel covers
contact. The covers still wanted to walk on the rim, so he added a bead of
silicone and has had no further trouble. Bob Brooks of Suffield, Conn.,
coated the wheel rim contact area on his 1952 Mercury with rubber cement and
hasn't thrown a wheel cover since. To hold the full disc, wheel covers on
his 1989 Thunderbird, Lou Frueh of Wickliffe, Ky., drilled a hole in the
wheel cover 180 degrees from the valve stem, then drilled and tapped a hole
in the wheel as near the rim as possible, and bolted on the wheel covers. He
disguised the bolt to look like another valve stem. Thomas Murray of San
Leandro, Calif., found that a strip of masking tape around the rim holds the
wheel covers on his two Kaisers in place. Bob Lewis of Susanville, Calif.,
uses silicone adhesive sealant to keep the full disc wheel covers on his
1950 Ford club coupe from moving. Gerald White of Altoona, Fla., observed
that the brake drum will keep the center of the wheel from flexing, but not
the rim, leading us back to Mr. Egan's warning about the danger of wheel
failure unless the rims are replaced by stronger ones designed for use with
radial tires.




From: Bob Jasinski <rpjasin@xxxxxxxxxxx>
Date: Wed, 12 Aug 2009 16:00:44 -0700
To: Chrysler 300 Club <Chrysler300@xxxxxxxxxxxxxxx>
Subject: [Chrysler300] Radial tires on Beautiful Brutes

 
 
 

Tony,
 
I took the subject as being all of our letter cars running radials.  Having
said that, if you do have the information from the accident investigator and
it would be easy for you to email it, I would like to see the data.  I do
forklift accident investigation work and I actually like reading reports
like you describe.
 
Thanks!
 
Bob J




[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.