Re: [Chrysler300] 413 oll pump

[Ray Jones <hurst300@xxxxxxxxxx>]

Instead of guessing, go to you well stocked Auto Parts Store and buy an oil pressure gauge kit. Not too much money and it's a good diagnostic tool.
Remove the Oil Pressure sender and install the line for the kit and then see what the pressure is. Then you'll know if it is, indeed, the pump or some other item in the system.
When done with this problem, put the kit in your trouble box for another time or install it and you'll be able to actually see the pressure instead of an analog "about this much" reading.
Ray




On Sep 25, 2011, at 7:51 PM, C Bilter wrote:

Hi Bob,

I agree with the folks who suggest looking at the sending unit first and
then the gauge or the gauge voltage limiter. At hot idle your engine
actually doesn't require a lot of oil pressure, but the gauge should not
read "zero." If you decide to change out the oil pump, here is an article I
recently wrote that is posted in the tech department on the club website
that might be helpful: http://www.chrysler300club.com/tech/joil/oilp.html 

300ly,

Carl Bilter

Current 300J and former G owner

_____ 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
Behalf Of Bob Jasinski
Sent: Sunday, September 25, 2011 5:40 PM
To: mgoodknight@xxxxxxxx
Cc: 'Chrysler 300 List'
Subject: RE: [Chrysler300] 413 oll pump

I have no problem with oil pressure above idle speed whether the engine is
hot or cold, the driving pressure is just fine, at least 1/2 to 2/3rds
pressure on panel gauge. The drop in pressure only happens after an
extended run, on a hot day, like when you come off the freeway and are at a
light in gear, or dead stopped on the freeway in traffic, with the engine
idle around 650-750 RPMs. The pressure literally drops to a zero reading on
the gauge, and that is what concerns me, especially if you are stopped in
traffic for long periods.. As I sit there looking at no pressure I envision
the bearings running with no lubrication and worry about it. This has
happened with two different brands and weight of oil, 10-30W and 10-40W, but
did not happen with the 20-50W. I also am running the prescribed amount of
Redline zinc additive, which I believe tends to thin the oil a bit. 

Maybe I should try a straight weight oil, but I think the problem could just
get worse with a straight 30W, as the viscosity won't increase with
temperature as do the multiweight oils. As I see it, the needle should at
least be at the bottom of the pressure indication, even at idle, not at
zero.

Bob

From: mgoodknight@xxxxxxxx <mailto:mgoodknight%40juno.com>
[mailto:mgoodknight@xxxxxxxx <mailto:mgoodknight%40juno.com> ] 
Sent: Sunday, September 25, 2011 2:22 PM
To: rpjasin@xxxxxxxxxxx <mailto:rpjasin%40pacbell.net> 
Subject: RE: [Chrysler300] 413 oll pump

Bob,
I should have added: the fact that you have lower oil pressure at idle
with 10w-40 does not mean that you have lower oil pressure at speed. It is
quite likely that your pressure is still being limited to around 60-70psi by
the pressure relief system. Supplying too much pressure to the bearings can
cause erosion of the soft materials that make the good bearing surfaces on
the bearing inserts. In race conditions that erosion risk is tolerated
because of frequent bearing changes.
Marshall Goodknight, retired engine failure analyst and long time engine
technician with Mechanical Engineering education
---------- Original Message ----------
From: "Bob Jasinski" <rpjasin@xxxxxxxxxxx <mailto:rpjasin%40pacbell.net> >
To: "'Bill Huff'" <czbill@xxxxxxxxxx <mailto:czbill%40cfl.rr.com> >,
<chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300%40yahoogroups.com> >
Subject: RE: [Chrysler300] 413 oll pump
Date: Sun, 25 Sep 2011 13:24:26 -0700

Because a year ago I changed the oil to 20-50W and the problem went away.
Last week I changed the oil back to 10-40W and the problem came back, so I
figure it is the pump, but I am open to suggestions as to other causes. 

Bob J 

From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>
<mailto:Chrysler300%40yahoogroups.com>
[mailto:Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>
<mailto:Chrysler300%40yahoogroups.com> ]
On
Behalf Of Bill Huff
Sent: Sunday, September 25, 2011 1:05 PM
To: Bob Jasinski; chrysler300@xxxxxxxxxxxxxxx
<mailto:chrysler300%40yahoogroups.com> 
<mailto:chrysler300%40yahoogroups.com> 
Subject: Re: [Chrysler300] 413 oll pump

What made you settle on the oil pump as the reason for low oil pressure?

Bill Huff

3:27 PM, Bob Jasinski wrote:
>
>
>I think it's time to replace the oil pump in my 300G. I'm noticing pressure
>is dropping to a very low level on a hot day after a long drive while in
>gear and idling (went to the Ironstone Concours in Murphys yesterday)
>
>I looked at Rock Auto, and they list 3 different oil pumps all from the
same
>manufacturer (Sealed Power) and one is standard, the second is
>"High-Volume", the 3rd is "High Pressure". Prices are only $10 more as you
>go up.
>
>What gives? Why should I go with a standard pump if the other two are so
>close in price? Is there a problem going with a non-stock pump? Could it
>blow out seals in an older rebuilt engine? Those in the know please share
>your knowledge on this.
>
>Thanks!
>
>Bob J
>
>[Non-text portions of this message have been removed]
>
>

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]

__________________________________________________________
<http://thirdpartyoffers.juno.com/TGL3132/4e7f9b7c236a473fdcfst04duc> Penny
Stock Jumping 3000%
Sign up to the #1 voted penny stock newsletter for free today!
<http://thirdpartyoffers.juno.com/TGL3132/4e7f9b7c236a473fdcfst04duc>
AwesomePennyStocks.com

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]





[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylangYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/