[Chrysler300] Re: 1963-64 Chrysler 300 J & K

[donald cole <mr300k@xxxxxxxxx>]

Hey J & RAM-K guys, I reconnected with my source and he is willing to reproduce more heat pipes. If the club members would let me know how many sets I should have him make would be a help. The cost is not certain as of yet. I should have them in hand within a couple of months. The last ones were $250 for a set of 4 pipes. I'm sure the cost has gone up in the last ten years. The ones he made had thicker flanges and pipe. They are probably the last ones you will ever need.
300kly,

Don Cole
On Nov 16, 2012, at 8:44 PM, Rich Barber wrote:

> Now, wait--the heat tubes are small OD--maybe 1" or smaller, with flanged ends that feed hot exhaust gas from ports on the cast iron exhaust manifold to and from a chamber underneath the carburetors on J's and ram K's--which are both equipped with aluminum short ram induction systems.  See attached picture.  Waldron's does a great job on the ram exhaust pipe system and conceivably could fabricate the heat tubes but it is not clear they know what we're talking about.  Let me know if Waldron's is on the same page as us before I go searching for a valuable set to use as a model.  Tolerances will be tight and there is room for improvement in materials used to avoid delay corrosion & burnout.  Waldron's expertise with aluminized and muffler-grade steel should prove valuable.  Before we proceed, we need to know Don Cole's plans for producing another batch through his previous supplier.
> 
> Rich barber
> 
> -----Original Message-----
> From: thomas r denkler [mailto:tdenkler3853@xxxxxxxxxxxxx] 
> Sent: Friday, November 16, 2012 4:03 PM
> To: c300@xxxxxxx
> Cc: ldmiklas@xxxxxxxxxxx
> Subject: Fw: 1963-64 Chrysler 300 J & K
> 
> Guys, do we know who might have a set of spare heat tubes to supply to Waldron Exhaust. Sounds like he might reproduce for us.
> 
> Thanks,
> 
> Tom Denkler
> 
> 
> -----Forwarded Message-----
>> From: Waldon's Exhaust <waldron@xxxxxxxxxxxxxxxxxx>
>> Sent: Nov 16, 2012 3:33 PM
>> To: 'Thomas Denkler' <tdenkler3853@xxxxxxxxxxxxx>
>> Subject: 1963-64 Chrysler 300 J & K
>> 
>> Hello Thomas,
>> 
>> The first statement we would like to address is " These are similar to 
>> the
>> 60-61 300's but are
>> exhaust heated not water heated."; The heater tubes on the exhaust pipe 
>> for
>> 1960-61 300 with the Ram Induction setup are exhaust heated, not water 
>> heated.
>> 
>> Our resources do not show a system available (in the reproduction 
>> world) for
>> 1963-64 300J/K with Ram Induction. We do have the system for 1963-64 
>> 300J/K series with the Cross Ram engine which does not have heater tube 
>> but has LS/RS exhaust pipes designed to fit to a 3rd pipe called a 
>> cross over (also called a balance tube). Please refer to the photos I have attached.
>> 
>> If you (or someone else) can send us the pipes we can use it as a 
>> pattern and build a jig.
>> 
>> Kind regards,
>> Ruth
>> 
>> Ruth E. Frisbie
>> Sales Administrator
>> Waldron's Exhaust
>> www.waldronexhaust.com
>> Ph# 800-503-9428
>> Ph# 269-467-7185
>> Fax# 269-467-9041
>> 
>> PLEASE - ORIGINAL MESSAGE MUST BE INCLUDED WHEN REPLYING. IT MAKES OUR 
>> JOB MUCH EASIER WHEN REPLYING TO YOU. WE NEED TO SEE ALL OF THE PRIOR EMAILS.
>> THANK YOU!
>> -----Original Message-----
>> From: Thomas Denkler [mailto:waldron@xxxxxxxxxxxxxxxxxx]
>> Sent: Wednesday, November 14, 2012 4:36 PM
>> To: waldron@xxxxxxxxxxxxxxxxxx
>> Subject: Message from waldronexhaust.com
>> 
>> From:	Thomas Denkler
>> Email:	tdenkler3853@xxxxxxxxxxxxx
>> 
>> ------------------------------------------------------
>> 
>> Can you please,please,please, and please consider remaking the 63-64 
>> Chrysler Ram heat tubes. These are similar to the 60-61 300's but are 
>> exhaust heated not water heated.They are a tad longer than 60-61.Noboby 
>> makes these and all 63-64 300 J/Kram owners are missing them. I assume 
>> they must have warped or bolts shifted, etc.
>> I bet @ 200 J//K owners would snap them up, because they also support 
>> the weight of the rams.
>> Thanks,
>> Tom Denkler
>> 
>> ------------------------------------------------------
>> 
>> Office Use Only:	
>> From:	Thomas Denkler
>> Email:	tdenkler3853@xxxxxxxxxxxxx
>> Login Name:	Not logged in
>> Login Email:	Not logged in
>> IP Address:	76.7.145.25 - 76.7.145.25
>> Host Address:	tn-76-7-145-25.dhcp.embarqhsd.net
>> Date and Time:	Wed Nov 14 2012 15:36:13 CST
>> 
> <Heat tubes-'64 300K.jpg>



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylangYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/