Re: [Chrysler300] Engine mounts and 300H Transmissions Al 727
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Engine mounts and 300H Transmissions Al 727





I learned a long time ago (too long) that with pans, both AT and Oil, to work the holes with a ball peen  hammer.
When they are tightened down, they tend to go concave and dig into the gasket.
After several time this "hump" around the hole prevents the pan from smoothly compressing the gasket.
By using a ball peen hammer centered on the hole, it can be made flat or humped to the bolt side.
Then when tightening the bolts down to specs, the whole gasket will be compressed evenly.
Ray


On Mon, Feb 24, 2014 at 6:23 PM, Michael Moore <mmoore8425@xxxxxxx> wrote:
 

Jim,

Inquiring minds want to know! I also am thinking I may as well buy an al cover. Can you tell me what "pan you bought? What gasket? s
Thanks, MIke Moore

On Feb 24, 2014, at 12:24 PM, Anna F Noia <sa-noia@xxxxxxxxxxx> wrote:

Jim
What aftermarket aluminum pan did you use for your 727? Did you go for the extra capacity? that helpes in keeping it cool(er), with the extra trans fluid, or so they say? Also, do you have an external trans cooler installed? The factory units mount in front of the radiator support and are hard plumbed, so I'm told. If you have one, what is the flow path of the trans fluid, does it still go through the radiator cooler then out to the trans cooler then back to the trans? Just curious on the routing for best cooling. Thanks in advance for insights.
 
Best Regards,
Stephen A. Noia
1-408-210-4736 cell
From: Jim Maiani <jmaiani@xxxxxxxxxxx>
To: Michael Moore <mmoore8425@xxxxxxx>
Cc: chrysler300@xxxxxxxxxxxxxxx
Sent: Monday, February 24, 2014 12:07 PM
Subject: Re: [Chrysler300] Engine mounts and 300H Transmissions Al 727
 
Mike  After about 3 different trans shops to try and stop the trans leak with my survivor H, the culprit was the pan.  The final trans guy told me the original pan was good for about 3 or 4 times coming off.  After that, the edges get so warped, 3 different places couldn’t stop the leak.  I replaced the pan with an aftermarket aluminum one and presto!  no leaks.
 
Jim Maiani
Houghton Lake, MI
H
 
 
Sent: Monday, February 24, 2014 2:34 PM
Subject: [Chrysler300] Engine mounts and 300H Transmissions Al 727
 
 
I picked up my car this morning with its replaced engine and tranny mounts . I had an NOS RF and a used LF, plus a new tranny mount from Jeff Carter. The reason I changed them out was that
I believe the engine wassitting too low which is hopefully why my fan blade was clipping the lower part of the shroud which happened after I changed out my fan clutch!
 
I was very surprised at the difference the "new" engine mounts made in terms of smoothness of idle ??? All I can imagine is that the engine rocking around was modulating the throttle linkage.
 
But now there's another issue to be resolved. transmission fluid leaks.
My mechanic (in the top 20 of 1900 in the Bay area)  added dye to the transmission this morning.
Tomorrow morning we will look for leaks on his rack.
Does any one have suggestions for the most common source of leaks?
 
Also, if it does have to come out and go to a shop he recommends to be resealed, does anyone know, or is there a club publication
about the differences between a 727 and a 300H 727? (I am anticipating a call about needing a rebuild etc. I really do trust this shop, even though the owner is Corvette afficianado :-)).
  
 
   Thanks for the help.
Mike Moore
300H




--
Ray Jones. Y'all come on down an see us. Ya hear?


__._,_.___


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang




Visit Your Group
Yahoo! Groups
PrivacyUnsubscribeTerms of Use

__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.