RE: [Chrysler300] Modifying 1957 WCFB carburetors to address "stalling o

Hello to All --

Nuts! I Forgot that the 300 Club list server would not accept my attachment of the Chrysler Service Bulletin 1034-CH on modifying the WCFB carburetors! So, if any individuals are interested and cannot find the bulletin elsewhere (maybe other members have that bulletin available, also), please contact me and I will send it to you outside of the server! You will probably still want to follow up on the jetting and metering rod recommendations to make the modifications all work together. The 300 Club Forward Look Archives contain my original messages from late 2012, as well as John Chesnutt's listing of metering rod part numbers -- I used his p/n's to provide the Carburetor Shop with the exact dimensions for the new (leaner) metering rods and jets that I had Jim McGowan install.
> For archives go to
> http://www.forwardlook.net/300-archive/search.htm#querylang

Ray Melton

> From: finsruskw@xxxxxxxxxxxxxxx
> To: rfmelton@xxxxxxx
> Subject: RE: [Chrysler300] Modifying 1957 WCFB carburetors to address "stalling on turns"
> Date: Wed, 25 May 2016 13:12:46 -0500
>
> Only one problem, Ray...
> Our antique list server will not allow ANYTHING!!!
> Other than chit chat!
>
> -----Original Message-----
> From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
> Behalf Of Ray Melton rfmelton@xxxxxxx [Chrysler300]
> Sent: Wednesday, May 25, 2016 12:58 PM
> To: chrysler300@xxxxxxxxxxxxxxx
> Subject: [Chrysler300] Modifying 1957 WCFB carburetors to address "stalling
> on turns"
>
> Chrysler did indeed issue a Service Bulletin in 1957 to address the stalling
> problem in the WCFB carburetors. See the attached Bulletin and redlined
> corrections thereto. I bought the new jets and metering rods from The
> Carburetor Shop, bought the required drills, and provided the parts and
> Service Bulletin to Jim McGowan, who performed the modifications on my
> WCFB's, in addition to rebuilding, re-plating and RESTORING the carbs to
> like-new condition. Beautiful job!
>
> After installation, the carbs were easily brought into "fine tune" while
> sitting in the shop; however transmission problems have kept the car from
> getting on the streets to verify that "the fix" actually works on turns.
> Hope to have it back in action within a couple more months!
>
> Ray Melton
> Las Cruces, NM
> 1957 Chrysler 300C cvt

> From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
> Behalf Of Ray Melton
>
> Sent: Monday, November 05, 2012
> 5:25 PM
>
> To: 'Larry Jabin'; 'George
> McKovich'
>
> Cc: chrysler300@xxxxxxxxxxxxxxx
>
> Subject: [Chrysler300] Modifying
> 1957 WCFB carburetors

> Regarding the modifications outlined in the Factory Service Bulletins, you
> will also note that in addition to drilling some new holes and enlarging
> some passages, they specify changing to new metering rods in both
> carburetors and different secondary jets in the front carburetor, none of
> which are available any more. However, since I am planning on having those
> modifications made to the WCFB's on my 300C, I have searched for quite a
> while and finally found a source for the elusive parts. John Hardgrove at
> The Carburetor Shop in Eldon, MO (573-392-7378) will make the new rods for
> you on the original machines purchased from Carter when they went out of
> business in the '70's. These unique, totally manual machines from the 1940's
> can hold precision tolerances down to 0.00005" (five hundred-thousandths of
> an inch - about one hundredth the diameter of a typical human hair!)
> However, that kind of precision machining does not come cheaply: the rods
> cost $320/set of four and you must also purchase their WCFB rebuild kit @
> $154 for two carburetors. The new secondary jets are a paltry $15/pair. So,
> I'm looking at
> $489 + $14 shipping just for the parts for the rebuild, PLUS the labor for
> the restoration itself! This is likely to be a ~$1100 job! (subsequent
> note: Make that a $1350 job!)
> The best part about having these new metering rods custom-made is that John
> has all the original Carter part numbers and specs as well as the
> Carter-original tiny brass billets, so he can also make the new metering
> rods in the standard configuration as well as three more stages of "lean" to
> adjust for high-altitude operation. John Chesnutt wrote on December 15, 2008
> listing the Carter P/N's for these different metering rods. I can forward
> that message to any interested member if you are unable to locate it
> yourself.

> Ray Melton
> Las Cruces, NM
> 1957 Chrysler 300C convertible
> White/Gauguin S/N 3N572517
>
> From: Ray Melton [mailto:rfmelton@xxxxxxx]
> Sent: Monday, November 05, 2012 1:08 PM
> To: 'George McKovich'; Larry Jabin
> Cc: chrysler300@xxxxxxxxxxxxxxx
>
> Subject: RE: [Chrysler300] Carbs ?s for 1958 Chrysler 300D

> There was an additional Chrysler Service Bulletin No. 1034-CH issued October
> 16, 1957 to correct a misprint in Service Bulletin No. 1028-CH (August 30,
> 1957). That misprint affected the dimensions of the modification to the
> carburetors; to wit:
> Quote: "Please note on Page 2 of Service Bulletin No. 1028-CH in Figure 1,
> under the drawing of the "Air Horn" the Primary side should be 11/16 inch
> and the Secondary side should be 13/16." (The drawing in #1028 had these
> dimensions
> reversed)
>
> Ray Melton

> On Nov 5, 2012, at 9:10 AM, Larry Jabin <larry@xxxxxxxxxx
> <mailto:larry%40pwbsfo.com> > wrote:
> > When taking off from a stop light at an intersection where I have to
> > make a left turn, If I take off quickly the car stumbles so I guess the fuel is moving
> > in the bowl to the right side of the carb. I thought I read somewhere on the list server for a fix for this, but
> can't seem to find it

Has anybody else experienced this & know of a fix?
>
Thanks
Larry Jabin

> For archives go to
> http://www.forwardlook.net/300-archive/search.htm#querylang