Re: {Chrysler 300} Question on installing spring clips for nose letters

Roberta

Sent from my iPhone

On Sep 5, 2022, at 2:07 PM, Ron Waters <ronbo97@xxxxxxxxxxx> wrote:

Rob -

The pin goes thru the hole. Then the retainer slides onto the pin on the back side of the hood.

From your photos it appears that you may have a layer of body filler that may impede the pin from sliding fully thru the hole. Please shoot a picture from underneath the hood showing how far the pin protrudes thru the hole.

Thanks,

Ron

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx [mailto:chrysler-300-club-international@xxxxxxxxxxxxxxxx] On Behalf Of Larry Jabin
Sent: Monday, September 05, 2022 1:46 PM
To: rob; Chrysler 300 Club International
Subject: RE: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

I have the same situation please include me an any reply’s

Thank You

Larry

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of rob
Sent: Monday, September 5, 2022 9:20 AM
To: Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

Hello 300 Group

About three months ago after a nice Sunday drive I discovered my LETTER

“S” on the hood nose of my 300 had disappeared. I suspect it just fell out.

I was able to find a replacement S from the Quigly company. It is

not chromed…but it will do. Then I learned I needed a set of spring clips

to properly attach it. I was able to get the spring clips…a set of 8!

Now the challenge of how to properly install it? I tried putting it in the hole

and gently tapping the clip. This did not work adequately. Then I tried

attaching it first to the post of the letter and gently tapping that into

the hole. This resulted in the post on the letter bending. Any advice on how

to properly install my new letter. I did think about using adhesive….

however the proximity to the radiator leads me to believe an adhesive will fail due to the heat.

I will be grateful for some good advice?

Here’s a few photos….

Thanks.

Rob

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/d240f85a-f0e6-467a-a58e-659aca6bb88bn%40googlegroups.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/8f136bc4a30749ab8fddf4b48111c2d1%40pwbsfo.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/ABA2D12B59E84BA3AACC545109A0D42E%40ThinkPadL520.

Re: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E