Re: {Chrysler 300} Question on installing spring clips for nose letters

Several folks have asked where you can get the spring clips to attach the nose letters. I checked with Quigley and he did not have any. But a fellow named John Begian offered me a package of 8 for $20. I think he is a 300 memberâ€¦his address is 9254 Sherwood Drive, Saline, MI 48176. He may have more. Good luckâ€¦

Those engineers at Chrysler really used their engineering skill when they developed the spring clips.

They do seem to get the job done.

Rob Lutts

Salem Massachusetts

1959 300 E Radiant Red

Robert T. Lutts, President and Chief Investment Officer

Cabot Wealth Management, Inc.

216 Essex Street

Salem, Massachusetts 01970

978-979-0880

www.eCabot.com

[EXTERNAL EMAIL]

Put the clip on the S and work it gently into the groove. When you have a slight purchase on the groove established ( meaning it can support the S without falling away) either apply force directly straight into the hole by your fingers or a gentle tap with a small rubber mallet. It needs to be a snug fit.I do not advise using any WD 40 or silicon lubricant because they can reduce essential friction between the S tong and the clip. Hope this helps. It is always a patient maneuver that for some reason I have to be by myself to finagle them in without bending the tong on the back of the letters or losing the clip. Hope this helps! 300â€™ly, Rob Kern

On Sep 5, 2022, at 12:45 PM, Larry Jabin <larry@xxxxxxxxxx> wrote:

I have the same situation please include me an any replyâ€™s

Thank You

Larry

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of rob
Sent: Monday, September 5, 2022 9:20 AM
To: Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

<image001.jpg><image002.jpg>

Hello 300 Group

About three months ago after a nice Sunday drive I discovered my LETTER

â€œSâ€? on the hood nose of my 300 had disappeared. I suspect it just fell out.

I was able to find a replacement S from the Quigly company. It is

not chromedâ€¦but it will do. Then I learned I needed a set of spring clips

to properly attach it. I was able to get the spring clipsâ€¦a set of 8!

Now the challenge of how to properly install it? I tried putting it in the hole

and gently tapping the clip. This did not work adequately. Then I tried

attaching it first to the post of the letter and gently tapping that into

the hole. This resulted in the post on the letter bending. Any advice on how

to properly install my new letter. I did think about using adhesiveâ€¦.

however the proximity to the radiator leads me to believe an adhesive will fail due to the heat.

I will be grateful for some good advice?

Hereâ€™s a few photosâ€¦.

Thanks.

Rob

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/d240f85a-f0e6-467a-a58e-659aca6bb88bn%40googlegroups.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/8f136bc4a30749ab8fddf4b48111c2d1%40pwbsfo.com.

Re: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E