RE: {Chrysler 300} RE: Front Suspension Lower Control Arm Procedure. (Mo

That is what I am thinking. My other issue is the OD of the bushing. The replacements are 15 thou larger in OD. I hope they will go in clean.

James

From: Cox <scooter465@xxxxxxx>
Sent: Thursday, September 14, 2023 11:48
To: James Douglas <jdd@xxxxxxxxxx>
Cc: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} RE: Front Suspension Lower Control Arm Procedure. (More)

Lower control arms should

Be tightened at normal

Ride height position.

If tightened at hanging

Position bushing would

Be destroyed when arm

Moves to ride height position. If you proof read the FSM I am shore you

Would find a lot of errors LOL.

Bob Haag

On Sep 14, 2023, at 2:18 PM, 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:

One thing I just found out is that the lower control arm bushing from one of the usual suspects has and OD of 1.520 while the ones that came out were 1.503. The bore on the lower control arm is 1.503 to 1.504. I am leery of a 15 thousand interference fit. That is a lot. The outer shells on these are not split. I may have to use some anti-seizing compound so these things will not buckle going in.

Anyone out there had an issue with these? I would suspect that they all come from the same single source someplace up the line.

James

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Thursday, September 14, 2023 10:05
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Front Suspension Lower Control Arm Procedure.

Hi all,

There is an inconsistency in the 1964 Service Technical Manual on pages 2-8 and 2-9.

On the installation of the lower control arm it states on item #1, “…DO NOT TIGHTEN the front nut until the full weight of the vehicle is on the wheels.” Then on item #10 it states, “…Tighten the lower control arm shaft, (the ¾ inch) nut to 180 foot pounds…”. Then on item #11 it says to, “…Lower the vehicle to the floor…”

So, can someone tell which is it? Tighten it with weight on the car or before you lower it? I suspect it is to be done after the car is on the floor and item #10 and #11 is just an error carried over from some older text. One would want the rubber bushings on the shaft to be “neutral” with the car on its wheels. If one tightened it first then it would rotate and load the rubber on the wheels and probably actually change the spring rate and the life of the bushing.

Thanks, James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617109EB7268DE5DCAD3F5C393F7A%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171815BB91420A28AE02CDB93F7A%40CY5PR19MB6171.namprd19.prod.outlook.com.

RE: {Chrysler 300} RE: Front Suspension Lower Control Arm Procedure. (More)