Re: Block Markings

[65 <65Val@xxxxxxxxx>]

Do lifters from a V10 engine fit your engine, Bill? If so ,here's a link I 
found to purchasing oversize lifters...

http://www.enginebuildermag.com/Article/2050/valve_lifter_caution_on_19942002_chrysler_80l_vin_e__w_v10_engines.aspx

Darwin/Victoria,BC/Canada
--'65 Cdn.Val.Custom 100 'vert
225/factory A833....eternal project
--'67 Dart GT 'vert...
273/904...now with "Collector" status
http://s41.photobucket.com/albums/e285/65val/

----- Original Message ----- 
From: <chymar01@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Monday, December 22, 2008 9:44 PM
Subject: Re: Block Markings


> As far as I know, no one sells them anymore. You could get the bores 
> bushed($$$).
>
> Mark
>
> ----- Original Message ----- 
> From: "Bill" <Y1TopBanana73@xxxxxxxxx>
> To: 1962to1965mopars@xxxxxxxxxx
> Sent: Monday, December 22, 2008 10:49:41 PM GMT -05:00 US/Canada Eastern
> Subject: Re: Block Markings
>
>
> Holy shit...really? That sucks! If that's the case, then my little
> project just did a BIG brake check...correct? Where the hell am I
> going to get .008 over lifters??
>
> Bill M
> 65 Coronet 500 'vert
>
>
> On Mon, Dec 22, 2008 at 10:42 PM, <chymar01@xxxxxxxxxxx> wrote:
> > According to my book, that means .008 oversized lifter bores.
> >
> >
> > ----- Original Message ----- 
> > From: "Bill" <Y1TopBanana73@xxxxxxxxx>
> > To: "62-65 Mopar List" <1962to1965mopars@xxxxxxxxxx>
> > Sent: Monday, December 22, 2008 10:12:39 PM GMT -05:00 US/Canada Eastern
> > Subject: Block Markings
> >
> > So I finally got off my lazy a$$ and am doing the cam in the
> > Coronet.In tearing it apart I noticed a diamond stamped in the block
> > on the block deck surface, in front of the left head, up near the
> > intake. Does this have any significant meaning? I know the short block
> > in this car is not original.
> >
> > Thanks
> >
> > Bill M
> > 65 Coronet 500 'vert
>
>
> ---- 
> Please address private mail -- mail of interest to only one person --  
> directly to that person. I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will protect 
> your privacy, reduce the total volume of mail and fine tune the content 
> signal to Mopar topic. Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
> [Non-text portions of this message have been removed]
>
>
> ----
> Please address private mail -- mail of interest to only one person --  
> directly to that person.  I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will protect 
> your privacy, reduce the total volume of mail and fine tune the content 
> signal to Mopar topic.  Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.