RE: '62 rear drums

[Dave64 <lt7dave@xxxxxxxxx>]

I have the correct puller and it works.  I don't need it anymore (since I went with a later rearend) if anyone is intersted in it.

Dave

--- On Fri, 3/11/11, Paul Lennemann <pjlenn@xxxxxxxxx> wrote:

> From: Paul Lennemann <pjlenn@xxxxxxxxx>
> Subject: RE: '62 rear drums
> To: 1962to1965mopars@xxxxxxxxxx
> Date: Friday, March 11, 2011, 7:06 PM
> 
> Here is the procedure I use with the correct puller. 
> Take the axle nut 
> off and put it back on backwards, turning it so it is flush
> with the end 
> of the axle.  Attach the puller and tighten it down
> tight using a fist 
> maul.  Then rap the end of center screw with the
> maul.  Having the nut 
> on backwards ensures that the end of the axle won't
> mushroom out from 
> all of the pressure.  Doing this two or three times
> (sometimes just 
> once) will usually get it to pop loose. and when it comes
> loose it will 
> pop.
> 
> Paul L.
> '63 Sport Fury
> 440/727
> http://www.1962to1965mopar.ornocar.org/ml-lennemann63.html
> 
> 62pluckedchicken@xxxxxxxxx
> wrote:
> > 
> > Got your puller over to Rob.. he's gonna give it a
> shot tomorrow 
> > morning... keep your fingers crossed ;)
> > 
> > Thanks
> > Rich Kinsley wrote:
> > > 
> > > Probably would work but I have one you can
> borrow.
> > > 
> > > Rich Kinsley '64 Dodge Polara 4dr 318poly
> w/goodies
> > >
> ======================================================================
> > > 62pluckedchicken@xxxxxxxxx
> wrote:
> > > > 
> > > > I can't find the puller in Gary's picture,
> but I did find this on a 300 
> > > > forum http://www.chrysler300club.com/rcmstuff/fairbanks/puller.html
> > > > 
> > > > has anyone tried this puller?
> > > > 
> > > > spigot2039@xxxxxxxxxxx
> wrote:
> > > > > 
> > > > > 
> > > > > There's a picture of the type puller
> used shown on the tech page. 
> > > > > 
> > > > > http://1962to1965mopar.ornocar.com/images/axlepullertm.jpg
> > > > > 
> > > > > I don't know if they are still made but
> I've seen used ones for sale at 
> > > > > swap meets.
> > > > > 
> > > > > Thanks,
> > > > > Gary H. 
> > > > > 
> > > > > -----Original Message----- 
> > > > > >
> > > > > >
> > > > > >I think he may have made his own
> puller... there is a puller listed on 
> > > > > >1962to1965mopar.ornocar.com? 
> 
> > > > > >
> > > > > >Is it on the Vendor page? 
> > > 
> > > 
> > > 
> > > Rich Kinsley '64 Dodge Polara 4dr 318poly
> w/goodies
> > > http://1962to1965mopar.ornocar.org/ml-kinsley64polara.html
> 
> 
> ----
> Please address private mail -- mail of interest to only one
> person -- directly to that person.  I.e., send
> parts/car transactions and negotiations as well as other
> personal messages only to the intended recipient, not to the
> Clubhouse public address. This practice will protect your
> privacy, reduce the total volume of mail and fine tune the
> content signal to Mopar topic.  Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> 
> 
>