Darwin/Victoria BC/Canada '65 Cdn.Val.Cust.100 'vert Slant 6/factory 4 speed
[AD removed for archives] ------------------------------------------------------------------- Erase wrinkles without painful injections with Nexiderm SP. Nexiderm SP is clinically proven to reduce wrinkles by 68% Start your free 14-day trial today! caadfBPb3n3t4a/Nexiderm -------------------------------------------------------------------
Joe is right, the small valve 915 heads came on the non-magnum 440 C body cars and Imperials in 67. I think everyone misses the real issue with 915 - 516 heads. Yes they will produce a higher compression ratio because of the chamber, but the chamber is the real advantage. A 906 head has some small inherent flow advantages, but the open chamber is not a squelch area chamber. I am including a great link to the first of three cylinder head articles. All three are a good read.
There were low performance 915's with the smaller 1.60 exhaust valves. And I think if you open up the 516's to the larger exhaust you have about the same head, although I don't know what they flow. Joe
Seems that Joe and I post about some of the same subjects, beers and years here, i will take any corrections as education.
It was hot out and phoenix is about 1500 feet , so corrected for sea level and the hot weather it was probably a 15.5-15.0 run..
Turned out it had a cast crank 440 with 915 heads....the fact the pig boat ramcharger weighs over 5000 pounds..we were pleased with the numbers.
we had a water pump fail on the run up to flagstaff last summer...got really hot before we shut down...cracked the crap out of the heads....tore it down...heads unusable...turned out they were the small valve 915s....
picked up a set of 516s from ebay recently. They cost about $100 with shipping. we had them cleaned and checked for cracks.
we've compared them to our 915 heads, we have yet to discover a difference...the ports and valves are indentical by our observations....both are closed chamber...stuffing clay and styrofoam into the ports to see where the 915s are larger have not showed a difference.
I am always amazed that one can read and read everything there is to read about mopar heads.
The bottom line is that there are people writing about this stuff and there are people that have the cast iron pieces in their hands and looking at them. We think the 516s are probably the most underrated of the mopar heads.
In fact it almost seems that the extra compression ratio of the closed chamber almost makes up for the smaller exhaust valve. I agree with Joe...put the big exhaust valve in the 516s and you have the 915 head.
A 1968 fury 8 3/4 rear axle housing bolts into any e-body challenger or barracuda..straight up... perfect fit...we've done three.
The "official mopar chassis manual" numbers do not support this fact...same kind of deal...fiction verus hardware.
[AD removed for archives] ------------------------------------------------------------------- Get a FREE* MP3 Player - yours to keep! Click Here Now! caadeMpbV1hOjf/MP3 Player Giveaway -------------------------------------------------------------------
---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
'62 to '65 Mopar Clubhouse Discussion Guidelines: http://www.1962to1965mopar.ornocar.org/mletiq.html.
[AD removed for archives] ------------------------------------------------------------------- Erase wrinkles without Botox! Nexiderm SP is clinically proven to reduce wrinkles by 68% Click here to start your free trial today. caadfBNb3n3t4f/Nexiderm -------------------------------------------------------------------
'62 to '65 Mopar Clubhouse Discussion Guidelines: http://www.1962to1965mopar.ornocar.org/mletiq.html.
---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
bOyW3N.