RE: A-Body Axle Choice?
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: A-Body Axle Choice?



Jim,

Just grind, cut the old perches off, get a new set and weld them on.

It is a good thing to check the angle of the pinion in relation to how 
the pads are welded on to the rear end. I have a nice big welding 
table and a jig to do it, but before I built all that, I just removed 
one side, left the other side on so I could get the angle the same, 
then after I welded the new one on, remove the other old one.

There are a million ways to do it. You want a pinion angle between 
6 to 4 degrees with springs.

Earl 

-----Original Message-----
From: Jim Ozolins [mailto:j_ozolins@xxxxxxxxxxx] 
Sent: Thursday, October 12, 2006 11:07 AM
To: 1962to1965mopars@
Subject: RE: A-Body Axle Choice?


That's to narrow the B-body perches for the A-body?

Jim





>From: "Earl H. " <earlh@xxxxxxxxxxxxxx>
>Reply-To: 1962to1965mopars@
>To: 1962to1965mopars@
>Subject: RE: A-Body Axle Choice?
>Date: Thu, 12 Oct 2006 10:07:53 -0600
>
>
>Thanks, I forgot to mention that...Easy to fix... Cost 8 bucks plus 
>welding...
>
>Earl
>
>-----Original Message-----
>From: Dustin Cloud [mailto:hell_fish_65@xxxxxxxxxxx]
>Sent: Thursday, October 12, 2006 9:58 AM
>To: 1962to1965mopars@
>Subject: RE: A-Body Axle Choice?
>
>
>The perches on the b-body axle are wider too.
>
>
>
>Dustin
>
>65 Barracuda "Commando V8"
>www.geocities.com/hell_fish_65/
>http://www.1962to1965mopar.ornocar.com/dustinc.html
>
>"If it jams force it, if it breaks it needed fixing anyway."
>
>
>
>
>
>
>
>
>
> >From: "Earl H. " <earlh@xxxxxxxxxxxxxx>
> >Reply-To: 1962to1965mopars@
> >To: 1962to1965mopars@
> >Subject: RE: A-Body Axle Choice?
> >Date: Thu, 12 Oct 2006 09:45:37 -0600
> >
> >
> >Jim,
> >
> >8.75 axles are a dime a dozen... Original A body housings are a bit 
> >hard to locate, but you don't need one. They go for crazy amounts. An 
> >early B body is an easy swap, just one inch wider.
> >Just use more off set on your rims.
> >
> >You can find any 8.75 housing and have it cut down to A body width 
> >for not to much money. Moser does it for $150.00.
> >You can even have C body axles cut and re-splined. This is not a hard 
> >as you think.
> >
> >Earl
> >
> >-----Original Message-----
> >From: Jim Ozolins [mailto:j_ozolins@xxxxxxxxxxx]
> >Sent: Thursday, October 12, 2006 8:20 AM
> >To: 1962to1965mopars@
> >Subject: Re: A-Body Axle Choice?
> >
> >
> >Everybody, thanks for all of the advice on the rear end choice!
> >Looks like it's overwhelmingly for the 8.75" but that it may be hard 
> >to find.
> >Gears should be readily available.
> >
> >I'll need different shock mounts, u-bolts, axle mounting hdwe. and a 
> >new fabricated driveshaft.
> >(I will phase-out the ball and trunnion joint while I am at it)
> >
> >Sounds like money errr.... fun!
> >
> >thanks all.
> >
> >
> >Jim Ozolins
> >'64 Valiant
> >
> >
> >----
> >Please address private mail -- mail of interest to only one person -- 
> >directly to that person.  I.e., send parts/car transactions and 
> >negotiations as well as other personal messages only to the intended 
> >recipient, not to the Clubhouse public address. This practice will 
> >protect your privacy, reduce the total volume of mail and fine tune 
> >the content signal to Mopar topic.  Thanks!
> >
> >'62 to '65 Mopar Clubhouse Discussion Guidelines:
> >http://www.1962to1965mopar.ornocar.org/mletiq.html.
> >
> >
> >----
> >Please address private mail -- mail of interest to only one person -- 
> >directly to that person.  I.e., send parts/car transactions and 
> >negotiations as well as other personal messages only to the intended 
> >recipient, not to the Clubhouse public address. This practice will 
> >protect your privacy, reduce the total volume of mail and fine tune 
> >the content signal to Mopar topic.  Thanks!
> >
> >'62 to '65 Mopar Clubhouse Discussion Guidelines:
> >http://www.1962to1965mopar.ornocar.org/mletiq.html.
> >
> >
> >
> >
> >
>
>
>----
>Please address private mail -- mail of interest to only one person -- 
>directly to that person.  I.e., send parts/car transactions and 
>negotiations as well as other personal messages only to the intended 
>recipient, not to the Clubhouse public address. This practice will 
>protect your privacy, reduce the total volume of mail and fine tune the 
>content signal to Mopar topic.  Thanks!
>
>'62 to '65 Mopar Clubhouse Discussion Guidelines:
>http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
>----
>Please address private mail -- mail of interest to only one person -- 
>directly to that person.  I.e., send parts/car transactions and 
>negotiations as well as other personal messages only to the intended 
>recipient, not to the Clubhouse public address. This practice will 
>protect your privacy, reduce the total volume of mail and fine tune the 
>content signal to Mopar topic.  Thanks!
>
>'62 to '65 Mopar Clubhouse Discussion Guidelines:
>http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
>
>
>


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

bSONJP. 
Or send an email to: 1962to1965mopars-unsubscribe@











Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.