RE: Info ‘64 fuses & sig =?Wind
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Info ‘64 fuses & sig =?Wind



I'm pretty sure that the fuse panel is held to the bottom of the dash 
with a single screw.

It is also very likely that the clear plastic cover for the fuse panel 
has been discarded since you don't mention it.  It was held on by three 
tabs and was to keep fingers out of the panel although it is pretty 
flimsy.

Also as far as I can remember, the turn signal flasher is not clamped or 
attached to anything except the wiring and just sort of sits (hangs) 
there.

I hope this helps.

Regards,

K.


David Bailey wrote:
> 
> 
> 
> I?m trying to read the abbreviations and amp sizes as labeled on my fuse 
> box from my ?64 Dodge B body. Age and handling partially obliterated 
> some of the markings. This is what I was still able to read (or guess 
> at) even with the harness and fuse block on the bench. Beginning from 
> top to bottom,
> (1.) Is unreadable but looks like size 75 A 
> (2.) Heat_AC 20A 
> (3.) Is BLANK (not wired / no fuse holder) Acc_RR-A/C 20A 
> (4.) Cigar_LTR 20A 
> (5.) Tail_Stop-DCR 20A 
> (6.) CLSTR_LPS 2A. 
>  The owner?s manual has very limited info. I?ll start searching through 
>  other shop manuals to see what I find.
> Secondly though, I?d like to know how this fuse block and the turn 
> signal flasher was originally secured in place to the bottom edge of the 
> dash under the radio control panel. I see three locking (mount?) tabs on 
> the back of the block but can?t seem to locate three matching square 
> holes anywhere to mount it. Same for the flasher unit. Where and how was 
> this secured? I see a large raised shoulder on the block off to the side 
> with a larger diameter recessed area and a smaller dia. through hole. 
> I?m wondering if this might have once held a clip to insert/hold the 
> flasher?   
> These were left to dangle freely by someone else and now I can?t seem to 
> find where they belong.
> Any help with the correct labeling, amp sizing and/or mounting method/ 
> location would be well appreciated!
> Dave B
>   		 	   		  
> _________________________________________________________________
> Hotmail has tools for the New Busy. Search, chat and e-mail from your 
> inbox.
> http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_1
> 
> --
> [Non-text portions of this message have been removed]
> 



Kevin R. Merkley
Thunder Bay, Ontario
64 Dodge 440 2dr HT (Cdn)
64 Dodge Polara 500 Convertible (Cdn)


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.