Re: Update oil pressure
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Update oil pressure



As mentioned to me from a Chrysler race engine engineer, it is better
to have high volume than high pressure. 10psi/1000 rpms is all that is
necessary. BTW all my muscle Mopars have had HVHP oil pumps, 40psi at
600rpm idle and 70 psi hot cruising.

On Sat, Sep 3, 2011 at 6:13 AM, Jacob Fox <imfast101@xxxxxxxxx> wrote:
> Well I noticed I can get either a high volume, a high pressure or both. Since I'm not running high rpms I was thinking just high pressure? I hate to put an oem pump in and have same problem..
>
> Sent from my iPhone
>
> On Sep 3, 2011, at 4:45 AM, William Spore <w.spore@xxxxxxxxxxxxx> wrote:
>
>> I replaced my oil pump with a high volume pump when I rebuilt the motor (340)and it will give you a little more oil pressure just by virtue of it being a high volume pump. I can run down the road on a hot summer day and carry 65-70 plounds oil pressure all day long.  Bill
>>
>> ----- Original Message -----
>> From: "Jacob Fox" <imfast101@xxxxxxxxx>
>> To: 1962to1965mopars@xxxxxxxxxxxxxxxx
>> Sent: Saturday, September 3, 2011 4:34:40 AM
>> Subject: Re: Update oil pressure
>>
>> Damn don't have a torque wrench anymore lol how about tighten till it's good and tight? :) I'm still up in the air whether to replace with standard oem pump or high pressure pump. Perhaps with high pressure I could go back with 10-30. Only thing that has me worried is the 10-15psi I'm getting at hot idle. A bunch of friends tellin me that's low for a Mopar...idk! So much info! :/
>>
>> Sent from my iPhone
>>
>> On Sep 2, 2011, at 10:04 PM, "Gary H." <62to65mopar@xxxxxxxxxxx> wrote:
>>
>>> Start up protection: packing the oil pump with Vaseline type petroleum jelly quickly primes the pump / system: open up the oil pump case to pack.
>>>
>>> Put a very small (tiny) amount of silicone sealer on the surface of the mating surface and install the gasket.  Cover the pump shaft and O ring with oil. Put a small (tiny) amount of sealer on the block.  Twist left and right while installing.  35 foot pounds torque the 4 bolts.
>>>
>>> Thanks,
>>> Gary H.
>>>
>>>
>>>> -------Original Message-------
>>>> From: Jacob Fox
>>>>
>>>> Just wondering, when I remove pump, is there a pushrod I need to be careful with I need to line up a certain way or might fall out and be a pain? You say pack, I didn't know if that was just for startup wear or holding something in place.
>>>>
>>>
>>>> On Aug 30, 2011, at 10:32 AM, "Gary H." <  wrote:
>>>>
>>>>> If the old pump is worn, why not replace?  Peace of mind for you anyway. If you do that, pack the new pump with Vasoline before you install it.
>>>>>
>>>>>> -------Original Message-------
>>>>>>
>>>>>> Would putting new oem replacement get pressure up when starting? My thoughts where I was getting "slip" in the old worn one.
>>>
>>> --
>>> --
>>> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>>>
>>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>>> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>>> --
>>> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
>>> http://groups.google.com/group/1962to1965mopars?hl=en.
>>
>> --
>> --
>> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>>
>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>> --
>> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
>> http://groups.google.com/group/1962to1965mopars?hl=en.
>>
>> --
>> --
>> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>>
>> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>> --
>> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
>> http://groups.google.com/group/1962to1965mopars?hl=en.
>
> --
> --
> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>



-- 
Steve
'63 Hemi Polara

-- 
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.