Re: Weatherstriping Adhesive Recommendation

[Donald Gallimore <dongallimore@xxxxxxx>]

It's being attached to metal. The weatherstriping is a soft foam and bends pretty easily so notching it should not be needed, I think.

 

(thanks for the response)
 

Akron Don Gallimore

From: Paul L. http://1962to1965mopar.ornocar.org/ml-lennemann63.html <pjlenn@xxxxxxxxx>
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Sent: Mon, February 4, 2013 10:16:45 PM
Subject: Re: Weatherstriping Adhesive Recommendation

I assuming that the weatherstrip is being attached to a metal surface.  If the 90 degree turn you need to make is a tight turn would it help to cut a wedge out of the inside radius of the weatherstripping to take some of the tension off?

Paul L.

On Sunday, February 3, 2013 1:47:26 PM UTC-6, Donald Gallimore wrote:

I'm trying to secure the weatherstripping on the convertible top above the
windshield for my '65 Satellite. It makes a 90 degree turn over each door adding
a lot of stree to the adhesive and I can't get good adhesion. I have both 3M
Super Weatherstrip and Gasket Adhesive PN 08001 and Permtex Super Weatherstrip 
Adhesive PN 81731.

Not sure which I tried and failed with but are these the right product or is
there something better? Or, do I just need to follow the instructions to the
letter?

Akron Don

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.
 
 

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.