Re: valve cover gasket question

[John deVries <corneliusdevries@xxxxxxxxx>]

Ok did not see your post with the part number. I like them because of the tabs that hold them in place for installation. There was cork only gaskets on E-bay or at least that's what the picture showed without the tabs.  Not knowing that the Fel-pro has cork in them I would have call them rubber gaskets. I have a spare set. They did not leak which was nice. I always seem to have problems on the 440 getting the back corner to seal. 

Sent from John

On Jun 24, 2013, at 9:10, "Gary H." <62to65mopar@xxxxxxxxxxx> wrote:

> Okay thanks. That was the part number I posted originally. I don't think there is any other gasket available now.
> 
> "Fel Pro VS11828R = uses evenly-sized cork particles evenly distributed throughout a rubber binder."
> 
> I was wondering if Bill knew of an all rubber (Silicone Rubber) for the Poly. 
> 
> Thanks,
> Gary H.
> 
>> -------Original Message------- 
>> 
>> Fel-pro part number vs11828 r rubber gasket set for 318 poly.
> 
> 
>> On Jun 24, 2013, at 7:47, Bill M  
>  wrote:
> 
>> Yes. It might take calls to a couple of parts houses though. Maps is likely
>> a good bet.
>> Bill M
>> On Jun 24, 2013 10:44 AM, "Gary H."  
>> 62to65mopar@xxxxxxxxxxx> wrote:
>> Thanks. Are rubber gaskets available for a Poly 318?
>> 
>> Gary H.
>> 
>> 
>>> -------Original Message-------
>> 
>>> I ALWAYS use the rubber gaskets as the cork split too easily. I
>> typically
>>> put a very thin skim coat of Ultra Copper on both sides, let it setup a
>>> little bit, then install it.
>>> 
>>> 
>>> Bill M
>> 
>> --
>> --
> 
> -- 
> -- 
> --
> Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> -- 
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
> 
> --- 
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/groups/opt_out.
> 
> 

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.