RE: Need a refresher on sealing intake manifold

["Hall, Ricky L" <ricky.l.hall@xxxxxxxxxx>]

Had really good luck when I did the top end on my 318 Poly last spring, using Hylomar on the entire metal intake gasket surfaces.  This sealed the water outlet ports perfectly.  First try used RTV around the water ports as most do, but it did not seal.  I had bubbling at the manifold, and Stanley steamer action at the tailpipes.  ; )

Threw away the foam front and rear pieces, and used Right Stuff.

You can get spray Hylomar on eBay, makes even and quick application much easier on larger gaskets like that.

Easier to find Permatex brand of Hylomar:
http://www.permatex.com/products-2/product-categories/gasketing/gasket-sealants/permatex-permashield-fuel-resistant-gasket-dressing-flange-sealant-detail

There is very little I would use RTV for, except caulk my house.  ; )


-----Original Message-----
From: 1962to1965mopars@xxxxxxxxxxxxxxxx [mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of JimJablonski
Sent: Tuesday, January 14, 2014 6:16 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: Need a refresher on sealing intake manifold

I am getting ready to install the intake on the stroker build and it's been a few years since the last time I did this - would someone scan below - what I remember as a good way to go about it?

It is iron heads and an Edelbrock CH-28 (dual plane).  Note that I had the heads cc'd by Muscle Motors and I believe Eric said they had to give the intake side a little haircut as well given they milled the block side quite a bit.

Here's what I think I do:

- cement a paper intake gasket to the intake side of the heads
- slip the intake on to see if it aligns. If not, glue on another gasket, etc
- pull the intake off
- throw a bead of RTV on the end rails
- pop on the valley pan and the end rail tabs
- here's where i am foggy - do I put RTV anywhere on the sides of the valley pan?  I know some people actually trim the sides that lay over the intake ports but i dont think i ever did this
- last step is to install the bolts and torque it down

Oh, I think I smeared RTV on the bolt threads as well?

Am I close?

Thank you,

Jim

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.