Re: Torqueflite fluid filling and capacity ??
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Torqueflite fluid filling and capacity ??



Thanks,

I am looking onto that but what I didn't say is that the engine is an old 331 Hemi with an 8-bolt hub.  I know where there is a manual bell housing and I'll see if a flywheel is available.

Dennis C.

On Saturday, January 18, 2014 9:20:36 PM UTC-7, Roger Pettigrew wrote:
I keep an old wore out manual flywheel that I use on my test stand, do you happen to know where you could borrow one
 
In a message dated 1/18/2014 9:31:31 P.M. Central Standard Time, denni...@xxxxxxxxx writes:
I would if I could but the reason I have to put the transmission on the engine is that the starter ring gear is on the converter.

Dennis C.

On Saturday, January 18, 2014 7:16:48 PM UTC-7, 64ragtop wrote:
Just to throw it out there, Dennis, what would happen if you just left
the converter out?  I don't know either, but someone around here
probably does.
If that wouldn't damage the tranny, and I don't see how it could, it
would certainly simplify the project.

BC


On 1/18/2014 2:37 PM, Dennis C. wrote:
> I have a Torqueflite that has been completely drained, both the pan
> and the torque converter.  The torque converter was drained by
> removing the plug on the converter.
>
> I need to attach it to an engine that I want to run for cam break-in.  
> The engine is not in a car, it is on a solid stand that will support
> it and the transmission.
>
> Question
> Can I just fill the converter through the drain and not remove it from
> the transmission and if so do I completely fill it or just put in a
> quart like when the converter has been removed?
>
> How much fluid should I put in the transmission?
>
> The transmission has a spline tail shaft so I was thinking about just
> using one of the plastic caps to keep it from leaking.
>
> My concern is that when I start the engine I would like to do a full
> 20 minutes or more for cam break-in at 2,000 to 2,500 rpm. I am open
> to any and all suggestions how to get this done, I need the
> transmission connected to be able to start the engine.
>
> Thanks
> Dennis C.
> --
> --
> --
> Please address private email -- email of interest to only one person
> -- directly to that person. That is, email your parts/car transactions
> and negotiations, as well as other personal messages, only to the
> intended recipient. Do not just press "reply" and send your email to
> everyone using the general '62-'65 Clubhouse public email address.
> This practice will protect your privacy, reduce the total volume of
> mail and fine-tune the content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google
> Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
> ---
> You received this message because you are subscribed to the Google
> Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> To unsubscribe from this group and stop receiving emails from it, send
> an email to 1962to1965mopa...@googlegroups.com.
> For more options, visit https://groups.google.com/groups/opt_out.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopa...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
 
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.