Thanks for your answer so far, I have the 60 FSM but the procedure is not
quite clear to me.
And ofcourse I would like to know what caused the situation in the first
place.
I agree with you that the bars aren't broken, I definetely wouldn't be
able
to drive my car to my work today then :)
I will try to figure out the correct adjustment procedure, allthough I
don't
have all the special tools that might be needed for the job..
And ofcourse no suspension shop in my country can help me out with this
problem :)
Thanks ,
Robert
----- Original Message -----
From: "debenson2" <debensonii@xxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Thursday, June 21, 2007 12:36 AM
Subject: Re: IML: front end height question of 1960 Imp
Hello, I just replaced the rear springs and shocks all the way around on
my 57, I only needed to adjust the torsion bars in the front....
man what a difference!!!
Our bars in the front are adjusted to raise lower and equalize the side
to
side height...There are adjusting nuts? on the ends and this can be done
by...If yours have not moved in a while try to soak them with deep creep
or a penetrating oil for a few days...
If your bars had broken you would really know it!!!
My bet is just an adjustment.
I will look in my fsm to see if they outline a procedure and email it to
you....
Torsion aire is great!
debenson2
road2recovery
Box 43873
Brooklyn Park, Minnesota 55443 USA
debensonii@xxxxxxxxxxx
1957 Plymouth V800
1956 Dodge wagon
1956 Dodge coronet
1955 Chrysler New Yorker
1999 Town & Country AWD
2001 Ram 2500 quad cab
2004 Jeep Liberty
----- Original Message -----
From: "Rob van der Es" <r.vdes@xxxxxxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Wednesday, June 20, 2007 4:55 PM
Subject: IML: front end height question of 1960 Imp
Hello fellow Imperialists,
Apart from wrestling with some electric gremlins lately, I am a little
worried about one other thing.
When I looked closely to my car today I found that the front end was too
close to the floor.
It never drawed my attention before and I guess something must have
happend when the car was on jack stands for almost a week with the front
wheels free of the ground.
Ofcourse I did not place the stands or the jack right under the torsion
bars, the stands where placed under the wide frame members (left and
right).
I was working then on the driver side cilinderhead, trying to get rid of
some broken exhaust manifold studs.
When I succeeded this job, I lowered the car and was too happy to notice
the fact that the front end was lower then before.
When I walked around the car today, I can not get rid of the idea that
something has happenend.. The car's front end is definetely a couple of
inches lower then before.
What is happening here? And more important, how do I correct this
situation.
I know there must be some adjusters but can I simply turn them to get
the
front end up again?
Btw, the car's front end height is equal when you compare left and
right,
it is just that the total front end (especially the lowest point of the
front bumper) is way too low to the ground.
Does anyone has an idea here?
THanks a lot,
Robert
----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please reply
to
mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with
everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
Back to the Home of the Forward Look Network