Re: IML: A-arm Bushings and Torsion Bar Adjustment

["Frederick Joslin" <fljoslin@xxxxxxxx>]

Robert:

I believe that you can fully remove the adjuster bolts and then replace them with no problem. I would apply penetrating oil and then remove them from the car. It is easier to remove them than tighten them if they are a littl fouled. Clean up the threads with solvent and a wire brush and check the condition.

 

When adjusting the height up count the number of turns it takes. If both torsion bars are in about the same condition, it should take close to the same number of turns for a level front end. You can adjust the bolts with the front end off the ground and then lower it to chech the ride height. I would suggest this since it put less stress on the bolts (and on you).

Note that you may have some "worn out" threads especially from rust, but if they are in a section of the bolt that you do not need to "bite" into for your ride height that will not matter. What you have to do is get past that section. This is not ideal, but if it is all you can do........     

 

----- Original Message -----
From: "Rob van der Es"
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: Re: IML: A-arm Bushings and Torsion Bar Adjustment
Date: Fri, 22 Jun 2007 16:34:35 +0200


Hello again Joe,

Thanks for your kind suggestions!

I will certainly take care not to strip the
fine threads of the adjuster bolts and the
anchors.
I will clean them thoroughly and soak them for a while with penetrating oil.

I have had a long search for replacement bolts
and anchors but I haven't found any ..
So I hope that my adjusters are not stripped
already , causing the low front end!

Ofcourse I will have a look at the front lower
suspension arms too while I am there, just to
make sure that the bushings are still there and
in good condition.

Thanks again,

Robert
----- Original Message ----- From: "Joe
Strickland"
To: "Imperial Mail List"
Sent: Friday, June 22, 2007 3:42 PM
Subject: IML: A-arm Bushings and Torsion Bar Adjustment


> Rob;
>
> Before you begin adjusting your torsion bars,
> see if you can clean the threads of the
> adjusting bolts with some brake cleaner or
> perhaps kerosene to get as much dirt etc. off
> of the threads as possible. Use of an old
> toothbrush or something similar might help.
> Then use a liberal application of penetrating
> oil on the adjusting bolts and levers and let
> them soak for a day or so before trying to
> make the adjustments. You might want to
> re-apply the penetrating oil to the bolts
> more than one time. It may be a real problem
> if you stripped threads on the bolts and/or
> the adjusting arm of the torsion bars. You
> might be able to find replacements, but there
> could be a long time to find replacements.
>
> Be sure to examine the A-arm bushings for
> missing chunks or completely gone bushings.
> As I mentioned before when these bushings
> disintegrate and fall out it allows the
> associated metal parts of the A-arms and
> steering elements to shift position enough
> that the steering parts (especially the idler
> arm and the steering pitman arm) to shift
> position and get in quite a bind while
> steering the car. You certainly don't want
> to wind up with a broken idler arm stud or
> pitman arm stud while driving down the road!
> Complete loss of control might result, with a
> crash into another car or into a pedestrian
> or bicycle rider.
>
> Joe S.
>
>
> ----------------- http://www.imperialclub.com -----------------
> This message was sent to you by the Imperial
> Mailing List. Please reply to
> mailing-list@xxxxxxxxxxxxxxxx and your
> response will be shared with everyone.
> Private messages (and attachments) for the
> Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
> To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
>
>



----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial
Mailing List. Please reply to
mailing-list@xxxxxxxxxxxxxxxx and your response
will be shared with everyone. Private messages
(and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm

Fred Joslin