Re: [FWDLK] New or repro gas tank - 56 Plym
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [FWDLK] New or repro gas tank - 56 Plym



What you did was great but you should have coated the inside with sloshing
compound to seal it from corrosion.  Available from bill hirsh or POR 15
supplier

-----Original Message-----
From:   s scott [SMTP:kneedrager@xxxxxxxxxxx]
Sent:   Monday, February 22, 1999 7:30 AM
To:     L-FORWARDLOOK@xxxxxxxxxxxxx
Subject:        [FWDLK] New or repro gas tank - 56 Plym

I have a real bad fuel tank rust problem in my 56 Savoy.  As a temporary
measure I removed the tank, used a power washer inside and out, then
took a bunch of white gravel pebbles from the lawn put them in the tank
(removed the sending unit first) shook it around real good while
flushing it with the hose for about 1/2 hour.  I can at least get gas to
the carb now to move it around the driveway. This will do until I come
up with a permanent solution.

I have found a place that can clean and treat the inside with a rust
preventative, but it costs about $175, for that kind of money I figure I
can probably get a new tank.  I have struck out looking on the net and
all the guys that inhabit the local swap meets and shows. Any ideas
where I can get a new or repro tank, Or what model years may be close
enough to fit in the stock location?
Thanks
Scott


>From owner-l-forwardlook@xxxxxxxxxxxxx Sun Feb 21 14:54:38 1999
>Received: from PSUVM.PSU.EDU by LISTS.PSU.EDU (IBM VM SMTP V2R2)
>   with BSMTP id 9123; Sun, 21 Feb 99 17:53:44 EST
>Received: from LISTS.PSU.EDU (NJE origin LISTSERV@PSUVM) by
PSUVM.PSU.EDU (LMail V1.2c/1.8c) with BSMTP id 3940; Sun, 21 Feb 1999
17:53:44 -0500
>Received: from LISTS.PSU.EDU by LISTS.PSU.EDU (LISTSERV-TCP/IP release
1.8c)
>          with spool id 7605 for L-FORWARDLOOK@xxxxxxxxxxxxx; Sun, 21
Feb 1999
>          17:53:43 -0500
>Received: from PSUVM (NJE origin SMTP@PSUVM) by PSUVM.PSU.EDU (LMail
>          V1.2c/1.8c) with BSMTP id 3934 for <L-FORWARDLOOK@PSUVM>;
Sun, 21 Feb
>          1999 17:53:43 -0500
>Received: from mail.rdc1.ct.home.com (24.2.0.66,37596) by PSUVM.PSU.EDU
(IBM VM
>          SMTP V2R2) with TCP; Sun, 21 Feb 99 17:53:42 EST
>Received: from c61389-a ([24.2.153.78]) by mail.rdc1.ct.home.com
(InterMail
>          v4.00.03 201-229-104) with SMTP id
>          <19990221225346.OADC19602.mail.rdc1.ct.home.com@c61389-a> for
>          <L-FORWARDLOOK@xxxxxxxxxxxxx>; Sun, 21 Feb 1999 14:53:46
-0800
>MIME-Version: 1.0
>Content-Type: text/plain; charset="iso-8859-1"
>Content-Transfer-Encoding: 7bit
>X-Priority: 3
>X-MSMail-Priority: Normal
>X-Mailer: Microsoft Outlook Express 4.72.3110.5
>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3
>Message-ID:
<000f01be5dee$b074d940$4e990218@xxxxxxxxxxxxxxxxxxxxxxxxxxx>
>Date:         Sun, 21 Feb 1999 18:05:34 -0500
>Reply-To:     Ron Waters <ronbo97@xxxxxxxx>
>Sender:       Forward Look Mopar Discussion List
<L-FORWARDLOOK@xxxxxxxxxxxxx>
>From:         Ron Waters <Ronbo97@xxxxxxxx>
>Subject:      Re: [FWDLK] gas tank problem
>To:           L-FORWARDLOOK@xxxxxxxxxxxxx
>
>If there is evidence that your tank is leaking from anywhere, you
should get
>it fixed immediately.  It may only be leaking from the area where the
filler
>tube mates with the tank, but you may also have a rust situation in the
tank
>itself.  Either way, pull the tank (remove gas first) and inspect with
a
>flashlight.  If it is rusty inside, discard it and get a new one.  The
fuel
>tank is the same for all 57-59 Plymouths and Dodges (except wagons).
I've
>seen two varieties, but they both have the same part number, so they
should
>be interchangeable.  Once you've located a new one, or if the tank
looks
>shiny inside, dry it out, then coat it with gas tank sealer, like the
stuff
>available from Bill Hirsh.  I've used this and it's great.  When
>reinstalling the filler tube, be sure that the notch is pointing
straight
>up, since this is used to vent air out of the tank as it is being
filled
>with gas. BTW, there is a drainage plug in the bottom of the tank.  DO
NOT
>try to remove this plug.  If you do, you'll never be able to reattach
it,
>since the seal inside is dried out and brittle.  These plugs also have
a
>tendancy to leak.  When I had my tank out, I removed the plug and had
the
>hole soldered shut by a radiator repair shop.  Good Luck !
>
>Ron
>


______________________________________________________
Get Your Private, Free Email at http://www.hotmail.com




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.