For those of you still playing fuel pump trivia at home, I have more info that just keeps getting weirder and weirder-Upon closer inspection, I have the following to report:As for the Autozone replacement pump that is currently on the G (that I'm not sure I trust)I have the following info/numbers-On the box, and my receipt, is model number A1064MP (Mechanical Pump).Also on the box, is printed A13132191TGInside the box is a little ziplock bag containing an instruction sheet and two gaskets. On the outside of the ziplock bag is a stick on label that says M3672BD. Zoiks! the famous number M3672 some of you mentioned in the thread. it appears nowhere else.On the web page, specs for minimum 2 psi and 20 gal/hr are listed.On the O'Reilly pump I might switch to, the model M16077 is printed on the box and my receipt.Stamped on the actual pump itself is M20116, followed by the number 25349.No additional tags or numbers are on the documentation/installation papers in the box, so no reference to M3672BD anywhere. Specs listed on their web page say 4-5.5 psi and 30 gal/hr.The pump I took off the G has a sort of sunburst circular pattern similar to what can be found on alternators to be used with a magic decoder ring that I don't have. In the center of the sunburst is the number 84. On the opposite side from this stamping is another stamping that says Made in USA.Just for kicks, I looked on the box that my replacement pump for my Hurst came in, and it says A1142MP (Mechanical Pump) on the box and receipt, as well as A13132255TG. There are no specs for pressure or flow rate on the web page for this pump. It only states that it fits 1970 Chrysler 300 equipped with U code 440 engine. It's been on the car for a while now with no issues.On the actual pump I took off of the Hurst, is a stamping that says 484541C.Feel free to make any of this make any sense. I couldn't find any info on M20116 on the internet, and when I searched on the 484541C stamping on fuel pump I took off the Hurst, it returned results referencing International Harvester equipment. Pretty funny.On Sun, Aug 16, 2026 at 1:01 PM 'Ron Waters' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:--Personally, I wouldn’t trust any modern fuel pump from a chain auto parts store. Cheaply made foreign junk. On my 55 Desoto (possibly the same as C300?), I located a used correct factory fuel pump. Carter 2241S. Then I rebuilt it with a kit from Then and Now. Once on the car, it started up and no problems since.
One of the issues with modern pumps is that they put out too much pressure, which can result in issues with the needle and seat. Also flooding of the carb. John, you may want to pressure test your Autozone pump. Should not be more than 5-7 lbs.
Ron
From: chrysler-300-club-international@xxxxxxxxxxxxxxxx On Behalf Of John Nowosacki
Sent: Sunday, August 16, 2026 9:56 AM
To: ALLAN POZDOL <apozdol@xxxxxxxxxxx>
Cc: pffkllc@xxxxxxx; Jay Williamson <letterpressman@xxxxxxxxxx>; Carl Bilter <cbilter@xxxxxxxxx>; Keith Langendorfer <keith_a_lang@xxxxxxxxx>; chrysler-300-club-international@xxxxxxxxxxxxxxxx
Subject: Re: {Chrysler 300} fuel pump question/recommendation
I picked up one of these from the local Autozone:
After installation, I drove about 45 miles to a car event with no issues/leaks/smells. I stayed for about 2 hours, as it was getting hot outside, and the following happened-
I left the show and drove about 2 miles to the entrance ramp of the highway I was taking home, and my car got up to about 50 mph and would go no faster, started to stumble if I tried to give it more gas pedal, as if it was fuel starved. This lasted about 10 seconds, which felt like a lot longer, but then the situation cleared up and I drove home at about the 75 mph speed limit. When I got off the highway onto secondary roads, the car stalled at the first stop sign I came to. Car started right back up, then went the rest of the way with no issues. I had never experienced anything like vapor lock or fuel starvation, etc. with the old pump, but it was dripping/leaking fuel, which is why I changed it.
The new pump bolted right on, had the correct fitting for my gas line, and both inlet and outlet were in the same positions as the one I took off the car, but I don't trust it at this point, and will be returning it for a different unit and hope that all is well after that.
.
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion visit https://groups.google.com/d/msgid/chrysler-300-club-international/001401dd2da9%243327eb40%249977c1c0%24%40comcast.net.
--
Back to the Home of the Forward Look Network
Archive Sitemap