RE: [Chrysler300] Seat Belts & "Boots"

[Doug Warrener <dwarrener@xxxx>]

Mike, I did not include the material folded back on itself. I extended the
belt to it's maximum length and measured end to end. I can measure the
length that is folded back for the stitching if you need that info. Doug W.

-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxx]
Sent: Tuesday, November 18, 2003 4:21 PM
To: Doug Warrener
Subject: Re: [Chrysler300] Seat Belts & "Boots"


Doug, did your measurement include the material folded back on itself and
stitched at both ends of each belt? Exactly how did you measure each side?
Mike PS: The WESCO folks are great. Thanks for the tip.
----- Original Message ----- 
From: "Doug Warrener" <DWarrener@xxxx>
To: "'Mike Zagata'" <mzagata@xxxx>
Cc: <Chrysler300@xxxxxxxxxxxxxxx>
Sent: Tuesday, November 11, 2003 12:54 PM
Subject: RE: [Chrysler300] Seat Belts & "Boots"


Mike and Guy,I purchased sealt belts for my 300H from WESCO PERFORMANCE; 215
Ramona Pl.; Camarillo,Ca 93010. E-mail " wesco performance.com ", Phone:
805-738-0223. Cost was $24.00 per set, and the item no. is LL74-02, I think.
I measured my old "H" belts last night. The belting measurement on the
buckle piece is 45", and on the insert piece is 22-1/2". Hope this helps.
You might also try Snnake-Oyl as someone else suggested. They will restore
my old original belts for about $180 for both sets.

-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxx]
Sent: Monday, November 10, 2003 1:07 PM
To: Doug Warrener
Subject: Re: [Chrysler300] Seat Belts & "Boots"


Doug, I am interested. Thank you for getting back with me. Mike
----- Original Message ----- 
From: "Doug Warrener" <DWarrener@xxxx>
To: "'Mike Zagata'" <mzagata@xxxx>
Cc: <Chrysler300@xxxxxxxxxxxxxxx>
Sent: Monday, November 10, 2003 11:45 AM
Subject: RE: [Chrysler300] Seat Belts & "Boots"


Hi Mike, I know where you can purchase new after market belts with the "J"
hooks. I have a set in my 300H. They are almost equal to originals. I have
no idea where you can find the anchor assemblies. If you are interested, let
me know and I will look up the source tonight. Doug Warrener

-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxx]
Sent: Monday, November 10, 2003 7:08 AM
To: Chrysler300@xxxxxxxxxxxxxxx
Subject: [Chrysler300] Seat Belts & "Boots"


Hello fellow club members. I'm new to the club, but not to Chrysler. I was
lucky enough to be sponsored by Mopar while racing max wedges in the 60s.

I am in need of 2 "sets" of seat belts for the 62 or 63 Chrysler bucket-seat
cars (Chrysler 300, Plymouth Sport fury, Dodge Polara 500) (1 set = male
insert with belt and anchor end and female buckle with belt and anchor end).
The belt material has a fine 4-weave pattern (as opposed to being uniformly
course) and can be black or tan. Each anchor end consists of 2 flat pieces
of metal with a "J" hook on one end and a rectangular slot for the belt in
the other end. The two flat pieces are held together by a small machine
screw and lock nut. I need 8 of the flat plates with "J" hooks.

The "J" hooks pass through an "eye" bolt which passes through a large, flat
washer, then through a hole in the floor, where it screws into a plate with
a nut welded onto it. I need 4 eye bolts, 4 large washers, and four plates
with nuts.

Last, but certainly not least, I need the black vinyl "boots" or sleeves
that cover the 2 plates and anchor bolt for each belt segment. Each boot is
about 7 inches long, flat for most of its length and then flares out to form
a round base with 2 "ears" for the metal plates. I need 4 of these - 1 for
each belt segment.

[Non-text portions of this message have been removed]



To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to
http://www.chrysler300club.com/yahoolist/inst.htm

To unsubscribe from this group, send an email to:
Chrysler300-unsubscribe@xxxxxxxxxxxxxxx



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/