Re: [Chrysler300] using Steering wheel pullers

["Charlie Valentine" <cross.ram@xxxxxxxxxxx>]

Excellent advise !!!!!  I always leave the nut flush with the shaft and have had a few that could have been damaged as they were very stubborn to break free. 

One more tip....tuck the horn wire inside the steering shaft or you could either damage the wire or worse yet, shear it off.
Charlie Valentine
  ----- Original Message ----- 
  From: christopher beilby 
  To: MRS954@xxxxxxx ; jerrylindsay.300h@xxxxxxxxxxx ; Chrysler300@xxxxxxxxxxxxxxx 
  Sent: Saturday, September 16, 2006 2:48 AM
  Subject: [Chrysler300] using Steering wheel pullers


  Jerry and other 300 owners decide for yourselves, but for an extra measure 
  of 'avoiding possible uneeded hassles', rather than totally remove the nut 
  that holds the steering wheel, many undo it, but only until the top of the 
  nut is flush/level with the top of the threaded shaft, then use this 
  combined larger area for the puller centre to sit against, then when the 
  wheel pops loose, remove the puller, and undo the nut completely, and the 
  wheel will also just come off with no further puller needed.

  This way their is no risk of crushing the often hollow steering shaft, nor 
  damaging the beginning of the threads - however steering wheels are not that 
  usually stuck that this happens, but this can be more important if using a 
  puller on say a rear axle shaft or some more stubborn threaded item.

  Your decision, but make sure when first freeing/undoing the nut, before 
  fitting your puller, check that whatever, the nut is turned at least a 
  couple of full turns, so it leaves enough free space for the wheel to 'pop 
  up off free' of the shaft when pulling.

  If this seems complicated it is not - maybe I just need to learn to write 
  things more simply so no misunderstandings, and apologies to all those who 
  already knew all this - have a nice weekend,
  Christopher in OZ

  >From: MRS954@xxxxxxx
  >To: jerrylindsay.300h@xxxxxxxxxxx, Chrysler300@xxxxxxxxxxxxxxx
  >Subject: Re: [Chrysler300] Steering wheel puller
  >Date: Fri, 15 Sep 2006 12:24:02 -0400
  >
  >Jerry,
  >Auto Zone has those steering wheel pullers in their loan-a-tool program. 
  >You can also buy them, they are not expensive and you could use it in the 
  >future. It's basically a heavy gauge round plate with a bunch of holes, 
  >and a bag of various size bolts. First remove the large nut from the 
  >steering shaft. On the wheel puller, a large bolt goes in the middle hole 
  >and smaller bolts go through other holes and into the threaded holes in the 
  >face of the steering wheel. I don't remember if it's two holes or three. 
  >You thread in the small bolts evenly and then tighten the large bolt down 
  >against the steering shaft. Keep turning the large bolt. The pressure 
  >between the round plate and the shaft will push against the small bolt 
  >heads and thus pull the wheel off the shaft. When re-installing the wheel, 
  >look for a flat on the shaft and line it up with the missing groove on the 
  >wheel hub. Install the washer and nut, tighten until the wheel is firmly 
  >seated. Drive and enjoy.
  >
  >Regards,
  >Mark Souders
  >300H
  >Mohrsville, PA
  >
  >
  >
  >-----Original Message-----
  >From: jerrylindsay.300h@xxxxxxxxxxx
  >To: Chrysler300@xxxxxxxxxxxxxxx
  >Sent: Fri, 15 Sep 2006 10:24 AM
  >Subject: [Chrysler300] Steering wheel puller
  >
  >
  >I am in need of a steering wheel puller or directions for removing my 
  >steering off my 62 300. I have seen them on ebay at a rather cheap price. 
  >Would Autozone or places like that carry them. Also is there anything I 
  >need to lookout for or be careful of. Thanks in advance.
  >
  >Jerry Lindsay
  >Seminole, Fl.
  >727-393-9091
  >
  >[Non-text portions of this message have been removed]
  >
  >
  >
  >__________________________________________________________
  >Check out the new AOL. Most comprehensive set of free safety and security 
  >tools, free access to millions of high-quality videos from across the web, 
  >free AOL Mail and more.
  >
  >
  >[Non-text portions of this message have been removed]
  >
  >
  >
  >To send a message to this group, send an email to:
  >Chrysler300@xxxxxxxxxxxxxxx
  >
  >For list server instructions, go to 
  >http://www.chrysler300club.com/yahoolist/inst.htm
  >
  >For archives go to http://www.forwardlook.net/300-archive/
  >Yahoo! Groups Links
  >
  >
  >
  >
  >
  >
  >
  >
  >



   

[Non-text portions of this message have been removed]



To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/