RE: [Chrysler300] Garage Plans
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Chrysler300] Garage Plans



Not just bigger, also taller. Height does not cost much. I would not do less
than a 14' plate height. I am thinking of 16' for my new garage. That way
you have plenty of room for a mezzanine. Cheap space for office and storage.

Thank you,
Gary, the parts doc
Escondido, CA 92026 USA (New address)
Avocado territory.
Mail: garythepartsdoc@xxxxxxxxxxxx
760 751-1958






  -----Original Message-----
  From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx]On
Behalf Of Ray Jones
  Sent: Tuesday, January 17, 2012 4:01 PM
  Cc: Chrysler 300 Broadcast
  Subject: Re: [Chrysler300] Garage Plans



  Always exciting to plan.
  I agree with Billlll. If you have the room, go bigger. It usually does not
cost much more.
  If you talk to anyone who built a shop, you will NEVER find one who will
say It's too big.
  My shop is 30 X 50 and was here when I bought the property. I added a 23'
X 60' car open shed on one side. I bought used roof metal at an auction and
it was 23' long, just right, paid $50 for the stack and still have some left
over.
  My shop can be seen on the 300 Clubs website in the tech section. I wrote
an article about installing a lift in my shop which has 10' sidewalls. I
built the lift into the center truss and used it as a support. Lift cost was
$1850.00 delivered, 5 yrs. ago, may be cheaper now, get on the email list
and watch for sales.

  I love the lift, well built, USA made and here's the contact:

  American Automotive Equipment
  3 Rye Ridge Plaza
  Port Chester, NY 10573
  Phone: +1 914-690-9010
  Email: sales@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

  Building a shop bigger works along the lines that once they are pouring
the slab, bigger is just a little more framing and a few more yards of
concrete. Same goes for the trusses and walls. Price wider trusses, see what
the cost of adding 10 more feet to the length would be and again, if you
have the room, beggar is more gooder.

  In your area, cold is the rule I guess, so use at least 2X6 walls, and
ONLY use cellulose insulation. 12' side walls, minimum. and keep in mind
that a real lift needs 12' 6" for an overhead lift. These keep the cables
and hoses above going from one side to the other. Avoid the ones that have
these going across the floor from side to side. A royal pain when using a
jack under the car.

  Panel the ceiling and add 8" of cellulose across the top. At the bottom of
all the walls, trim with 2 X 6 treated lumber (so wet won't hurt it) and
then you can use drywall up from there for 1 row. Second row use 3/4"
plywood all the way around the shop so you can attach whatever anywhere you
want and don't need a stud. Drywall the rest. Ad 4 rows of shop lights, I
have about 20, 2 bulb lights and each row is on a separate switch. I also
built a office/storage/parts room in one corner, 10 X 20'.
  Do ALL this before the first car comes in or you'll never get it all done.
Once you start working in it, clutter keeps you from finishing.

  My cabinets came from Harbor Freight. They still have them, watch the ads
for sales on them. They are metal with metal pegboard backs, come with 3
shelves for each and pegboard hooks and shelf supports. They are about 4'
long and 30" tall and most importantly only 8" deep. You can't bury anything
way in the back to never be seen again.

  AS to heat, I have Geo-therm and it costs me $35.00 a month averaged over
2 years, to heat and cool. I keep it @ 75° in the summer and about 60° in
the winter, I may turn it up or down depending on how much I'm working in
it.

  A heated floor will make a lot of difference also, but more bucks to
install, but may save on heat later. Look into it.

  Last, talk to several contractors, shop owners, builders and suchlike and
ask for their experiences/recommendations doing quality jobs in your area.

  Good luck, Ray in Arkansas.

  On Jan 17, 2012, at 5:20 PM, Bill Leahy wrote:

  charlie, i built my new garage 24x30 and wished i had 30x30 / these dang
cars are longer than ya think / billllllll in windy kennewick, washington

  On Jan 17, 2012, at 3:17 PM, charlies@xxxxxxxxxxxx wrote:

  > Hi Group,
  > While this does not directly relate to 300 autos, it will someday be the
home and restoration centre for these beasts. I'm in the planning stages of
building a workshop for my wrenching - tired of working on gravel and at
minus whatever. The size of the wokshop will be 24 x 40 and will have a
lift. I'd be interested to hear any sort of recomendations that any members
may have in regard to my new wokshop - what worked well or didn't work well
in some of your shops - or what they may have done differently or added.
Thanks to all, Charlie in Ottawa, 62 Sport
  >



  


[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylangYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.