Re: [Chrysler300] Brake and fuel system advice for my '55
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Brake and fuel system advice for my '55





I just want to add that I have used Karp's Brake Service for a number of years now and have always been very satisfied with them.  I live only about 25 minutes away from them and they are my "go to" brake service guys when I need them.  

Jeff is the owner there and just first class - a genuinely nice guy!

Steve Albu

On Thu, Feb 6, 2020 at 7:11 AM Joe Allen billandmarilynallen@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 


Jim:

I should have replied earlier.  For 23 years I put up with poor brakes in my '55C300.  Last year I rebuilt my master cylinder /  booster myself, recognizing that it really needed to be re-sleaved..  Brakes performed even worse.  Upon referral by John Lazenby I sent my master cylinder / booster to Karps.  It was returned to me quickly, re-sleaved, better than new, a work of art!  For the first time in 23 years I now have fantastic brakes on my '55C300, thanks to John Lazenby and Karps.  By separate email, not on this forum, I will be glad to send you some pictures.

Good Luck!

Bill Allen

On Wed, Feb 5, 2020 at 7:17 AM John Lazenby french_fryguy@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 

Here is a source on the power brake that can and will rebuild it correctly.  I've used them for years and nothing but excellent work and good prices:  Custom Brake Shop | Karps Power Brake Service



John Lazenby


On Tuesday, February 4, 2020, 09:22:39 PM PST, 'Ron Waters' ronbo97@xxxxxxxxxxx [Chrysler300] <chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:


 

I highly recommend that you rebuild one system at a time.
 
Fuel tank: Look inside. If it's clean and doesn't leak, put it back.
Sending unit: Test it with an ohm meter as you move the arm up and down. If you see it's responding to the movement within the 90-10 range, then it's good. Put it back in the tank with a fresh seal.
 
Power Brake master cylinder: This is a unique, one year only m/c. Many places won't touch it. There is a kit supplied by Harmon Industries for rebuilding. Or they will rebuild it for you. These are the only folks that can successfully rebuild it. I rebuilt mine using a spanner tool to remove the rear disk.
Power Brake booster: Same information as above. Again, I purchased the rebuild kit from Harmon and did it myself. But they will rebuild it for you as well.
 
 
Ron
 
 


From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of Jim Jungwirth jk-jungw@xxxxxxxxxxx [Chrysler300]
Sent: Tuesday, February 04, 2020 10:27 PM
To: chrysler300@xxxxxxxxxxxxxxx
Subject: [Chrysler300] Brake and fuel system advice for my '55

 

My car has not run in many years, so I’m diving into my car’s brake and fuel systems, I pulled the fuel tank, going to have that checked over. The master cylinder is out, I still need to remove the booster.

 

Wondering what is the best way to go for a fuel sender and brake master cylinder replacement/rebuild and brake booster rebuild. Later on, I will be rebuilding the rest of the brake system. I’m looking for advice, in part, because I’m wary of the quality of new parts these days.

 

I’ve seen the prices vary quite a bit for the new fuel senders. Mine may be relatively old because it has a cork float on it. Is 90-10 ohms the correct resistance? Is rebuilding the way to go for these? Is there a preferred vendor for new ones?

 

There seems to be no new master cylinders available. I know White Post Restorations does master cylinder relining and booster rebuilds. Booster Dewey also rebuilds boosters.

 

I appreciate any and all help.

 

Thanks,

 

Jim

 

 

 

 

Sent from Mail for Windows 10

 



__._,_.___

Posted by: "Steve ." <saforwardlook@xxxxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang




Visit Your Group
Yahoo! Groups
PrivacyUnsubscribeTerms of Use

__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.