RE: {Chrysler 300} Drivers power window rats nest 300K

The one that is $350 is supposed to be NOS. I think that guy on eBay is toll that listed parts that other have in stock as when I asked for a photo I got grief.

I put in an email to MMPAR or whatever Franks successor named the biz.

If I cannot get an NOS one then Murry will me my next call.

James

From: pffkllc@xxxxxxx <pffkllc@xxxxxxx>
Sent: Tuesday, May 2, 2023 08:55
To: James Douglas <jdd@xxxxxxxxxx>
Subject: Re: {Chrysler 300} Drivers power window rats nest 300K

$350 seems pretty expensive, unless you are talking about an NOS motor. Try contacting Murray Park in Tiffin, Ohio. I'll bet he hs one or more.

Just Google him.

Pete Fitch

-----Original Message-----
From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
To: James Douglas <jdd@xxxxxxxxxx>; Bob Merritt <bob@xxxxxxxxxxxxx>
Cc: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Mon, May 1, 2023 2:35 pm
Subject: RE: {Chrysler 300} Drivers power window rats nest 300K

Can someone confirm for me that the mechanism (gear box and motor mount) is MOPAR 1963-827 ?

I found one for $350 and want to make sure that it is the part before I try and order it. Also in the master parts book it says that the front door mechanism is the same side-to-side but my memory is that they were side specific which makes me wonder if I have the wrong part number from the book.

Thanks, James

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Monday, May 1, 2023 09:30
To: Bob Merritt <bob@xxxxxxxxxxxxx>
Cc: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} Drivers power window rats nest 300K

Hi Bob, I did that in the past on the other cars. The swinging of the door on closing and the abrupt stop is causing the G-force of that motor to try and rip off that casting…

I need to order up a full set of leathers and washers for the car. I am going to see of I can find another mechanism for that door and rebuild it and swap out the one that is a mess.

You can see in the photo that the brace was cut. Also, the hole and the long screws in the gear box. All in all a mess.

James

From: Bob Merritt <bob@xxxxxxxxxxxxx>
Sent: Monday, May 1, 2023 08:04
To: James Douglas <jdd@xxxxxxxxxx>
Subject: Re: {Chrysler 300} Drivers power window rats nest 300K

One thing many of us have done is rig up

a strap from the door frame to the motor so the diecast is supported.

Bob

On 5/1/2023 9:48 AM, James Douglas wrote:

Thanks Bob, I am going to need a complete set of the washers as they appear to be completely gone. I will order as full set for the car as sooner or later I will do all the windows.

I HATE the diecast housing on these regulators. I had nothing but trouble with them in the past with the bottom of the housings cracking off at the motor mounts. Going through this again was one of my largest concerns on purchasing another 64.

I have contemplated having the housing scanned and seeing what it would cost to have a set machined from billet aluminum.

James

From: Bob Merritt <bob@xxxxxxxxxxxxx>
Sent: Monday, May 1, 2023 03:30
To: James Douglas <jdd@xxxxxxxxxx>
Subject: Re: {Chrysler 300} Drivers power window rats nest 300K

Hey Mr D;

I may have a naked 64 door out in the shop, will check later this week when I get a minute.

The window gear, maybe you mean this one:

http://www.chrysler300club.com/tech/windowgear/1a.html

John Grady sells his parts through Forward Look Parts, see

https://www.forwardlookparts.com/product-page/1960-1961-replacement-power-window-gearbox-gear

Give a shout if you need anything else.

Bob

On 4/30/2023 6:57 PM, 'James Douglas' via Chrysler 300 Club International wrote:

Hi All, I took the door panel off for the first time on the 300K. It is a good news bad news sort of thing.

The steel inside the door and down on the bottom of it looks like it left the factory last month. Stellar. The door panel has some warping on the bottom, but I think I can wet it and press it back to flat.

The window regulator is another story.

Someone with little knowledge got in there and really screwed it up. The one thing I know for sure is the gear is bad. I did not see it on the club website. Is the person who was making the gears in the tech section sill making or have them?

Also, if anyone has a door panel off on a ’63 or ’64 could I trouble you for a photo? I think someone cut and messed with the brackets that hold the motor and regulator to the webbing. I photo would help me to figure out what it should look like.

Thanks, James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171AA3583BF0DC2022D0AAF93699%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171F2C90B9A066CAB96FF36936E9%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617100E2129AB028564328B9936E9%40CY5PR19MB6171.namprd19.prod.outlook.com.