[AD removed for archives] ------------------------------------------------------------------- Get 4 Free low-fat, low-carb recipes caacOlyb7yoMza/PermissionData -------------------------------------------------------------------
Here's a heater core for sale on ebay not sure if it will fit a 62? Item number: 4501935229
Schuyler V. Wrobel Artist & Illustrator On Nov 7, 2004, at 11:43 PM, Schuyler Wrobel wrote:
[AD removed for archives] ------------------------------------------------------------------- Free recipes to get you in shape caacOlCbNHQrta/PermissionData -------------------------------------------------------------------
I had this problem about 15 years ago so my memory a little fogged, the heater control valve was leaking like a sieve
so we took the heater-core out or maybe just the valve? anyway at the time there was noway to fix it or find a replacement
so we had it welded up. I remember the guy welded a penny on the end of the valve that was leaking, which of coarse
rendered it useless, but water could pass through without leaking. so, we stuck everything back in and put a inline
valve on the heater hose that flows into the heater core. so with a longer cable the same lever still controls how much
heat or hot coolant flows into the heater core but now the lever works in reverse. Probably not the best way to fix it
but thats what we came up with at the time. and yes, there is a big hole rusted through the floorboard under the gas
pedal which I covered with some sheet aluminum stuck into place with some roofing tar. again, not the best way
to fix it but it cost me nothing.
nowadays you can probably find a new heater-core or control valve on ebay
and someone on the list may have some better Ideas?
Schuyler
Schuyler 62 Dodge Dart 440 wagon w/ Poly 318 <http://www.1962to1965mopar.ornocar.org/ml-wrobel62.html>
On Nov 7, 2004, at 1:31 PM, Allen Sullivant wrote:
Hello,
Mine was leaking, so I bypassed it for the summer and forgot about it. Now I could use heat/defrost again, and I've piddled away the whole summer without fixing anything. So I just hooked everything up again and took a look.
When I crawl up under the dash, I notice no obvious leaks until I push the heat lever over to hot. Then water practically pours out from around the mounting bracket for the heater control valve. I would think that is my problem. The passenger floor is dry. The driver floor has several weak/rotted places where antifreeze got to it, and coolant drips on my shoe when it's on the gas pedal.
Question 1: Can you replace the heater control valve without taking the whole dang heater box apart? Looks like I can disconnect the heater hose and remove two screws on the flange and pull it out. I know there's an O ring seal where it fits into the core, which I can probably get at the hardware store.
Question 2: I found a used control valve and heater core on Ebay a few months ago, which appear to be OK. No way to tell if the valve is good unless I install it, right?
Question 2: Is there any relatively easy way to take the control valve out of the loop? Just run hose directly to the core or something? I don't mind having hot water in the core all the time or whatever. Don't mind it staying warm in the car. I had a '49 Hudson with an after-market Arvin heater once, and it kept hot water in it all the time unless I turned two knobs on some rigged up bypass in the hoses under the hood, which took the heater out of the coolant loop.
Thanks,
Allen Sullivant Brentwood, Tenn. 62 Dart 440 See-dan dart440@xxxxxxxxxxxxx
-- [Non-text portions of this message have been removed]
---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
b7yoMz.
Back to the Home of the Forward Look Network