Re: SS Springs brought back up again

[Layne Grissman <64Polara500@xxxxxxxxx>]

${top_text_ad}
For the setup. We jsut ordered the 3400# Set from Summit racing...they
also had the 2" extended Brackets needed, and with a little work, we
got them in there just fine....Everything bolted up beautifully....no
issues....these springs are for 62-65....and they fit perfectly. eith
the 2" extensions.

As for the lower hole...that's where they are right now...and She is
sitting mighty tall right now.....I will end up installing these to
the upper holes in the brackets just to see what differences there
are...I'll let you know as soon as I find out.....

I'll end up making the changes tomorrow night and seeing how that goes....


On Wed, Nov 25, 2009 at 12:28 AM, MO ( Steve Mick)
<micher@xxxxxxxxxxxxxxx> wrote:
>
> OK you have the thicker leaves on the right side-sounds right. My first
> thoughts are maybe the left side will settle down to level when you get a
> few miles on it ---or your right  front torsion bar does not have enough
> tension on it, or the left front torsion bar has to much tension on it.
> Lifting one corner , lowers the oposite corner.
> I am very interested in your set up. Where did you get the springs and are
> they for a 62-65 or for a 66 later?( trying to figger out when and when not
> to use the 2" extensions. Front eyebolt in the lower hole, does that raise
> the height of the body rear? And if you try the top holes, does that lower
> it and by about how much.  Don't change it just to answer my many questions!
> LOL.....................................MO
> ----- Original Message ----- From: "Layne Grissman" <64Polara500@xxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Tuesday, November 24, 2009 11:49 PM
> Subject: SS Springs brought back up again
>
>
>>
>> Tonight, I got the new Mopar SS Springs installed on the 64
>> Polara....Used the new 2" front brackets that they requested, and they
>> fit like a charm.
>>
>> Everything lined up fine until I put Betsy on the floor to see how she
>> stood.
>>
>> I hear all of you guys saying she should be higher on the right hand
>> side...(Passenger side) than on the left hand side....(Drivers side)
>>
>> I've got a weird one here...First of all I checked the part
>> numbers.,..All correct....Springs are much thicker on the Passenger
>> side as expected....but here is the kicker...
>>
>> When we let her down, She is tilted the wrong way....the Drivers side
>> is raised.....Not the passengers side as was discussed in previous
>> threads...
>>
>> Any ideas?  I did everything right as far as I know in the
>> replacements....
>>
>> The new brackets come with two holes in the for mounting....shoulld I
>> go up to the top hole on both to see if that fixes it?   I'm at a
>> loss...
>>
>> Thanks for your help in advance,.....
>>
>> Layne
>>
>>
>> ----
>> Please address private mail -- mail of interest to only one person --
>>  directly to that person.  I.e., send parts/car transactions and
>> negotiations as well as other personal messages only to the intended
>> recipient, not to the Clubhouse public address. This practice will protect
>> your privacy, reduce the total volume of mail and fine tune the content
>> signal to Mopar topic.  Thanks!
>>
>> '62 to '65 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>>
>>
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and negotiations
> as well as other personal messages only to the intended recipient, not to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to Mopar
> topic.  Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
>

${bottom_text_ad}
----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.

This email was sent to: ${recipient}

u/?bUrDWg.${encoded_sub_id}.${EMC}