On the subject of speakers, what size fits in the stock dash location of my 65 Belvedere vert? Is it 6x9 or a 5x7. Those retrosound units look good and the price seems right. Mike P. Sent from my iPhone On Dec 10, 2009, at 11:37 PM, "Dennis C." <dennis.2914@xxxxxxxxx> wrote: fyi There are a couple of sources for speakers with dual voice coils that I have found. This allows a single speaker to be connected to a stereo receiver. I am installing a 6"X9" in the frong and rear of my 63 SF. No idea how it sounds yet but I'm expecting it to be usable. http://www.casmfg.com/DVC_Speakers.htm http://www.retrosoundusa.com/products/category/id/8 I was not going to cut the doors for speakers and didn't want two speakers in the package tray. Dennis C. Steve Charette wrote: Dooner, I trust that I can plug my Sirius radio into this somehow?? The ReadiRad looks cool but if I'm reading right I'm still stuck with the OE electronics (or lack of), and the OE speaker. I like your setup! Thanks, SC -----Original Message----- From: Dooner [mailto:doonerfunderburk@xxxxxxxxx] Sent: Wednesday, December 09, 2009 10:18 PM To: 1962to1965mopars@xxxxxxxxxx Subject: Redneck Radios I just received an email asking what I meant by rednecking your radio (see below signature). Well, for those who didn't catch it when it was added to the restoration page of the 62 to 65 Mopar website, I will post this. REDNECK RADIOS: I convert your stock AM shaft style radio to AM/FM/AUX Input. ($150 or less). It is a lower priced alternative to the big boys out there.($350-$450) You will end up with the AM radio stock look, but with all new electronics inside. It will have two standard speaker output at about 10-15 watts each (L, R suggested use for two small speakers in dash center stock location), two RCA preamp outputs (L, R suggested use to the rear speakers with added small wattage amp), amp remote power on, bass boost, stereo/mono switch, and AUX input for CD player or MP3 player (Ipod). Some modifications have to be made to small cases and to stock radio knobs. The only thing you loose in this type of conversion, are all the preset buttons. Three of them become buttons for other uses. You can go here anytime to see it. Look in the electrical section. http://www.1962to1965mopar.ornocar.com/restoration-sources.html Dooner '64 Plymouth Belvedere 4dr Sedan Poly 318 + Push Button Auto Trans Contact me to redneck your radio. ---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks! '62 to '65 Mopar Clubhouse Discussion Guidelines: http://www.1962to1965mopar.ornocar.org/mletiq.html. 1996 Dodge Ram 3500 Van Conversion 1964 Plymouth Belvedere 318 Auto 1963 Plymouth Sport Fury 383 4-speed 1949 Dodge Pickup 289/C4 soon to be changed 1998 Honda Valkyrie Standard ---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks! '62 to '65 Mopar Clubhouse Discussion Guidelines: http://www.1962to1965mopar.ornocar.org/mletiq.html. ---- Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks! '62 to '65 Mopar Clubhouse Discussion Guidelines: http://www.1962to1965mopar.ornocar.org/mletiq.html.