RE: Mopar 383 engine tech
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Mopar 383 engine tech



We have had this happen several times and each time a lifter has jumped out of a bore!  Sometimes a pushrod is through a rocker if they are not "+" rockers. Sometimes a bent push rod. But always a sudden thing  once while driving down the road. We have never had a pump fail suddenly.

-----Original Message-----
From: Joseph Bitterman [mailto:furyrestored@xxxxxxxxx] 
Sent: Friday, May 06, 2011 12:02 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: Re: Mopar 383 engine tech

had a similiar thing happen to me and the felt that goes on the crank at the timing chain dissintegrated and found its way to the oil pump pickup!engine was running fine one minute and then started ticking and oil pressure dropped to zero i pulled the oil pan and found the felt was packed in the screen at the pick up thank god i was at home in the garage when this happened or it would have definately been a bad deal which i still had alot of time invested and such but luckily caught it right away and no damage done 

--- On Fri, 5/6/11, Stan Kafouse <skafouse@xxxxxxxxx> wrote:

> From: Stan Kafouse <skafouse@xxxxxxxxx>
> Subject: Re: Mopar 383 engine tech
> To: 1962to1965mopars@xxxxxxxxxx
> Date: Friday, May 6, 2011, 11:43 AM
> Try a new pump or drop pan to see if
> pick up is "sludged" etc. up. Had the same thing happen to me new pump 
> fixed it.  Oil goes from pump to passenger side lifter galley.  Oil 
> feeds mains from pass. lifter galley then up to cam. Oil goes from 
> pass. galley across rear of block to drivers side lifters.
> 
> --- On Fri, 5/6/11, MO ( Steve Mick) <micher@xxxxxxxxxxxxxxx>
> wrote:
> 
> > From: MO ( Steve Mick) <micher@xxxxxxxxxxxxxxx>
> > Subject: Mopar 383 engine tech
> > To: 1962to1965mopars@xxxxxxxxxx
> > Date: Friday, May 6, 2011, 5:23 AM
> > 
> > Hay all, today I got back to tinkering with the 64
> Sport
> > Fury with a late 60's 383. Checking the dwell,
> adjusting the
> > carb and playing with the timeing.  I got it
> starting
> > fairly well and set the idle at about 800 RPM with the
> lumpy
> > cam it has.  I noticed the top end was makeing increaseingly louder 
> > noise. It has hyd lifters and
> they were
> > working ok.  I checked the mechanical oil pressure quage and 0 oil 
> > pressure!! Previously oil pressure had
> been
> > fine until today. Of course I shut it right down.
> > 
> > It was running, so I know the intermediat shaft was working  the 
> > dist---but the oil pump?? Q uestion is, what is the route of the oil 
> > after it leaves the pump
> and
> > oil filter?  I  think  a bearing  either main or cam has turned , 
> > shutting off the oil to the
> guage
> > fitting and the valve train.  Any input is 
> > appreciated.............................MO
> > 
> > {Steve Mick}
> > http://stevemick1964dodge.shutterfly.com/pictures/5
> > 
> > ----
> > Please address private mail -- mail of interest to
> only one
> > person -- directly to that person.  I.e., send parts/car 
> > transactions and negotiations as well as
> other
> > personal messages only to the intended recipient, not
> to the
> > Clubhouse public address. This practice will protect
> your
> > privacy, reduce the total volume of mail and fine tune
> the
> > content signal to Mopar topic.  Thanks!
> > 
> > 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> > http://www.1962to1965mopar.ornocar.org/mletiq.html and 
> > http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> > 
> > 
> >
> 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER





Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.