The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

The quest for more caster.
Jump to page : 1
Now viewing page 1 [50 messages per page]		View previous thread :: View next thread
   Forward Look Technical Discussions -> The Exhaust Pipe - Modification & PerformanceMessage format
 
normsclassicradio
Posted 2024-04-20 1:14 PM (#634789)
Subject: The quest for more caster.



Extreme Veteran

Posts: 303
100100100
Location: Kalispell, MT USA		I have been updating the front suspension and brakes on my 1964 Dodge 880, same as Newport thru 63. I replaced the upper control arm bushings, and all 4 ball joints. I installed 1979 Cordoba spindles and disc brakes. The original specs call for very little caster even with power steering. Dialing in more caster leaves me with negative camber. Has anyone experimented with shorter strut rods to pull the lower ball joint forward a little and get more caster?
Top of the page Bottom of the page
Shep
Posted 2024-04-20 2:33 PM (#634791 - in reply to #634789)
Subject: Re: The quest for more caster.



Expert

Posts: 3399
20001000100100100252525
Location: Chestertown, NY ( near Lake George)		So how much caster can you get with acceptable camber? If you pull the strut rods forward enough to gain caster you will stress the lower arm bushings. Aftermarket control arms may be required.
Top of the page Bottom of the page
normsclassicradio
Posted 2024-04-20 3:00 PM (#634792 - in reply to #634789)
Subject: RE: The quest for more caster.



Extreme Veteran

Posts: 303
100100100
Location: Kalispell, MT USA		I would like to get 2 or maybe 3 degrees of caster while keeping .5 degree camber. See the before and after print-outs. I sacrificed camber for caster. This is not the final adjustment, just a rough-in after tweaking the steering arms on the Cordoba spindles and making sure I could get the toe-in close without modifying the tie rods themselves. I still am waiting for the idler arm rebuild kit.



(aling_before.jpg)



(align_after.jpg)



Attachments
----------------
Attachments aling_before.jpg (96KB - 7 downloads)
Attachments align_after.jpg (120KB - 9 downloads)
Top of the page Bottom of the page
wizard
Posted 2024-04-20 3:02 PM (#634793 - in reply to #634789)
Subject: Re: The quest for more caster.



Board Moderator & Exner Expert 10K+

Posts: 13050
50005000200010002525
Location: Southern Sweden - Sturkö island		Max caster should roundabout 1,5 degrees without disturbing camber. If you want more caster, Moog has offset uca bushings.
Top of the page Bottom of the page
Powerflite
Posted 2024-04-20 9:44 PM (#634798 - in reply to #634789)
Subject: Re: The quest for more caster.



Expert 5K+

Posts: 9673
5000200020005001002525
Location: So. Cal		Even with the offset bushings, you'll be lucky to get 1.5, or maybe 2 degrees. If you really want more than that, you'll need to modify your upper control arms. Cut a section out of the rear, and add a section to the front of it. The upper control arms on these cars aren't load bearing, so it isn't as dangerous as it sounds. But using shorter strut rods is just asking for stress and trouble.
Top of the page Bottom of the page
wizard
Posted 2024-04-21 8:41 AM (#634804 - in reply to #634789)
Subject: Re: The quest for more caster.



Board Moderator & Exner Expert 10K+

Posts: 13050
50005000200010002525
Location: Southern Sweden - Sturkö island		Yes Nathan, I managed to get 1 27/32 degrees Caster with -3/32 degrees Camber using the standard bushings.

Just to clarify, that is with radial tires.

If more Caster is wanted, I'd go for uca- modifications or even tubular uca (there should be some on the market)

As for uca modifications, I'd use a sleeve and weld it offside https://www.qa1.net/circle-track/rod-ends-ball-joints1/racing-ball-j...

The Moog offset bushing will surely not last as long as the standard ones.
Top of the page Bottom of the page
Powerflite
Posted 2024-04-21 10:52 AM (#634806 - in reply to #634789)
Subject: Re: The quest for more caster.



Expert 5K+

Posts: 9673
5000200020005001002525
Location: So. Cal		There are manufacturing variances, and it depends heavily on how much you have your car lowered on the t-bars. I use the offset bushings on all my muscle cars. Some get 1.2 degrees, some get 2 degrees. But the good news is that 1.5 to 2 degrees seems to be enough to create a stable ride compared to 0 degrees. That's an interesting idea to weld in a new offset ball joint socket.
Top of the page Bottom of the page
Shep
Posted 2024-04-21 11:56 AM (#634807 - in reply to #634806)
Subject: Re: The quest for more caster.



Expert

Posts: 3399
20001000100100100252525
Location: Chestertown, NY ( near Lake George)		I got 1.5 caster on my friends 59 Dodge, maintained good camber, car was level, radial tires, tracked very well. All new stock control arm bushings.
Top of the page Bottom of the page
wizard
Posted 2024-04-21 12:40 PM (#634808 - in reply to #634789)
Subject: Re: The quest for more caster.



Board Moderator & Exner Expert 10K+

Posts: 13050
50005000200010002525
Location: Southern Sweden - Sturkö island		Just another clarification; I have original ride height on my car.
Top of the page Bottom of the page
normsclassicradio
Posted 2024-04-22 4:51 PM (#634827 - in reply to #634789)
Subject: Re: The quest for more caster.



Extreme Veteran

Posts: 303
100100100
Location: Kalispell, MT USA		All great suggestions. However, I see adjustable strut rods available for later b body cars. Are they also known to stress the lower control arm bushings? I would have a hard time modifying the upper a-arm stampings. See the attached photos.



(upper arms.jpg)



(dynamic_strut_bars_52311-450x450.jpg)



Attachments
----------------
Attachments upper arms.jpg (99KB - 7 downloads)
Attachments dynamic_strut_bars_52311-450x450.jpg (10KB - 8 downloads)
Top of the page Bottom of the page
Shep
Posted 2024-04-22 6:17 PM (#634830 - in reply to #634827)
Subject: Re: The quest for more caster.



Expert

Posts: 3399
20001000100100100252525
Location: Chestertown, NY ( near Lake George)		If the struts are pulled forward excessively, you can see the pressure on the lower arm bushing, the issue is how far do you have to go to achieve the desired caster. If you look at the stock set up, they are not designed to be pulled forward for the purpose of caster adjustment. You would have to modify the inner bushing to gain any meaningful effect. Looking at the final settings from the shop, can't see how they left them that way, terrible. Check this link. https://www.forabodiesonly.com/mopar/threads/benefit-of-dynamic-stru...

Edited by Shep 2024-04-22 6:24 PM
Top of the page Bottom of the page
1960fury
Posted 2024-04-22 7:47 PM (#634833 - in reply to #634789)
Subject: Re: The quest for more caster.



Expert 5K+

Posts: 7402
50002000100100100100
Location: northern germany		? It is a logical consequence, that this will stress and wear out the lca bushing in a short time. Also, of course the lca needs to be in line with the torsion bar. So this is not the way to do it. 60 Plymouths have lots of overhang and lowered to the max (just driveable without too much tail dragging), it is still possible to get enough caster/camber with stock components, even though the upper bushings are stressed more. If I had the spare parts, I'd try modified uca's.

Edited by 1960fury 2024-04-22 10:22 PM
Top of the page Bottom of the page
normsclassicradio
Posted 2024-04-22 8:13 PM (#634835 - in reply to #634789)
Subject: Re: The quest for more caster.



Extreme Veteran

Posts: 303
100100100
Location: Kalispell, MT USA		The alignment report is just a first rough in adjustment. I'm doing it myself at the Dodge dealership I work at. I just want to have a plan for the next time I have it in the shop. I tweaked the steering arms to get the toe close enough to adjust with the adjustment sleeves. If I can find another set of upper control arms I may try taking 2 and making one. I'm inclined to just extend the front portion on the stamping, I will gain caster and camber doing it that way.



(upper arms crop.jpg)



Attachments
----------------
Attachments upper arms crop.jpg (75KB - 9 downloads)
Top of the page Bottom of the page
1960fury
Posted 2024-04-22 10:18 PM (#634837 - in reply to #634835)
Subject: Re: The quest for more caster.



Expert 5K+

Posts: 7402
50002000100100100100
Location: northern germany		If you cut it there, it will be more likely to crack and you have to worry about uca to frame bracket alignment (you will have to cut both sides). See the green line. Weld in a wedge shaped steel piece. Cardboard template first. The steel will be easy to bend, but secure the final position with 2 separate small steel pieces first, at the outer rails.



(uca.jpg)



Attachments
----------------
Attachments uca.jpg (76KB - 7 downloads)
Top of the page Bottom of the page
normsclassicradio
Posted 2024-04-23 6:02 PM (#634849 - in reply to #634789)
Subject: RE: The quest for more caster.



Extreme Veteran

Posts: 303
100100100
Location: Kalispell, MT USA		Hitting the pause button for a couple of weeks. The stock 64 brake booster turned out to be bad, and was probably not up to the task of the split disc/drum system anyway. I tried a stock Cordoba booster but it is too large and hits the valve cover and PS gear. So plan C is a A/B/E body master cylinder/booster that's smaller and has an off-set bracket. If that works, then back to suspension work.

Edited by normsclassicradio 2024-04-23 6:05 PM




(BOOSTER-MASTER CYL.png)



Attachments
----------------
Attachments BOOSTER-MASTER CYL.png (181KB - 8 downloads)
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)