RE: IML: Two questions about the 413 engine of a 1960 Imperial
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: IML: Two questions about the 413 engine of a 1960 Imperial



Hello, Robert;

I don?t think there is a big difference in using 20W50, rather than SAE30W,
especially in the colder months.  Considering your climate, I think I would
just switch to the 20W50 and use it without worry.   It should provide
adequate lubrication for startup, the only better thing to do would be to
install a pre-lube system (which runs an auxiliary oil pump to circulate oil
before starting), but even that won't help the cylinder wall wear caused by
startup, because the cylinder walls are lubricated by spray from the
rotating parts.  Also, during cold startup, you are running a much richer
mixture, so there is some inevitable dilution of the oil with raw gas -
that's another reason to make sure the engine is thoroughly warmed up each
time you start it.

Dick Benjamin

-----Original Message-----
From: mailing-list-owner@xxxxxxxxxxxxxxxx
[mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On Behalf Of Rob van der Es
Sent: Friday, June 16, 2006 12:28 AM
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: RE: IML: Two questions about the 413 engine of a 1960 Imperial

Hello Dick,

Thanks for your very clear answers! (as always a joy to read!!)
I am glad my message survived a quick death from your delete key LOL

Yes, I must admit I have had the bad habit in making short test drives
last year (because the car was registrated at that time, so I have to made
illegal short runs to sort things out..) so it might be wise to change
that oil even if it has been used for only 500 miles or so.

I am not planning to drive (or even start) the car with temperatures below
32F, so I think I will be safe with SAE30.
But ofcourse I can use 20W50 too, do you think it has any benefits to use
this grade?
I can imagine that a 20W50 is easier to crank around in an cold engine
then a straight SAE30, so lubrication with a 20W50 will be better at cold
starts then?? You see, I have always learned that a cold start will put
the most stress on an engine!
Anything you can do to make the lubrication during cold starts the best
will pay off in the end, so I have been told.

Thanks also for your suggestions with regard to the pre-ignition setting,
I have set it back to its former setting (16 degrees BTDC) and I am very
happy with it! So at the moment I will leave it there.

And yes, these cars are a delight to drive around town ..
Not only for the headturning power, but also for the overall feel of
quality. The 727 is the best automatic gearbox I have ever experienced,
even a new Mercedes doesn´t shifts that smooth!!
And throttle response is that good that you sometimes think that you are
driving a much lighter car!!

Thanks again,

Robert

Op Vr, 16 juni, 2006 3:20 am, schreef Dick Benjamin:
> I just returned from vacation, and found about 200 IML messages on my
> e-mail, most of which died a quick death under my "delete" key, but this
> one did catch my eye.
>
> On the oil change question, the reason to change oil is from
> contamination caused by starting the engine many times, especially if it
> is not run long enough to evaporate all the moisture that condenses into
> the oil.  If the engine has always been thoroughly warmed up by driving it
> 10 miles or so, it
> is safe to change it every 1500 to 2000 miles even if this takes more than
> a year.  However, if it has been started and stopped without a thorough
> warm up, I'd change it and the oil filter now, and then avoid this type of
>  operation in the future.
>
> As for the grade of oil, SAE30W was recommended when the car was new,
> unless the temperature was expected to be below 32F the next time the car
> was to be operated.  In your climate, if you feel you might want to use
> the car when it is below freezing when you start it, I think it is  OK to
> use 20W50 your car, in fact you can use that year round.  I would not use
> the 10W40 or 10W30 that is becoming so common now in that old an engine.
> Note that
> SAE30W does not mean "poor quality" oil or "non detergent" oil.  Many
> older Diesel engine and high performance engine manufacturers recommend
> using this oil, and premium grade oils in this grade are usually available
> in heavy equipment supply houses.  Using a Diesel rated oil is perfectly
> OK in a gas
> engine - it has a stronger detergent action - but this is a good thing!
>
> As for your pre-ignition questions - if you can set the timing so that
> the car runs well and you don't hear pre-ignition "pinging", you are not
> going to hurt the engine.  It is quite possible that your timing indicator
> has slipped on the crank pulley, and you are getting a wrong idea about
> where it is set.  I recommend just advancing the timing until you just
> barely can induce "ping" at part throttle at about 30 MPH, with the gas
> you plan to use in the car, and with the engine thoroughly warmed up.
> More acceleration
> should make the "ping" go away, and of course less acceleration will make
> it go away - just a tiny range of acceleration should be able to make it
> ping - that is the optimum setting, regardless of what the timing mark
> says.
>
> Throttle response with the 413 is superb - due to the design of the
> intake system and the AFB carburetor - that is one of the joys of driving
> these cars - that "snap" off the line.  Of course the 727 helps too!
>
> Dick Benjamin
>
>
> -----Original Message-----
> From: mailing-list-owner@xxxxxxxxxxxxxxxx
> [mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On Behalf Of Rob van der Es
> Sent: Thursday, June 15, 2006 2:29 AM
> To: mailing-list@xxxxxxxxxxxxxxxx
> Subject: IML: Two questions about the 413 engine of a 1960 Imperial
>
>
> Hi all,
>
>
> I would like to hear your expertise about two questions I have with
> regard to my 413 engine (1960 Imperial).
>
> Here is the story, I bought last summer in California a great 1960
> Imperial and after bringing it to Europe where I live (the Netherlands) I
> started to make the car ready for use on the road.
>
> I don't know the history of the car, I only know that it is a repo car.
> I bought it from a bank that had it for sale at an auction.
> As far as I can see and judge the engine must be a rebuild one, cause it
> is running powerful and smooth (can't imagine that I wouldn't have been
> overhauled in 46 years).
>
> I only have driven the car so far for a 500 miles or so and now it is
> ready and legally approved to use at a regular base (passed all the
> essential tests at the local DMV this monday!)
>
> Now we come to my first question: since I own this car almost a year now
> I
> think it is time to do an oil change allthough I only have driven 500
miles
> with the new oil that was poured in last summer in the US.
>
> What I would like to know is what kind of oil I should buy: a modern
> 10W40
> or a straight classic SAE 30 oil. From all the stories at the repair side
> of the club webpages I learned that a modern multigrade won't do any good
>  because of the very light base oil that is used (SAE10..). Thank you
> Dick
> for explaining that issue clearly as always!! But is it safe to use SAE 30
> singlegrade in a much colder environment then California??
>
>
> I would not drive the car at winters when it is freezing, but mainly on
> shiny days with temperatures between let's say 50 and 80 degrees outside
> temperatures. Would I be safe then or is 50 degrees to low to safely use
> SAE30?
> At the moment the engine is using a little oil, allthough I don't see any
> leaks or smoke at the tailpipes. I am almost sure the workshop that
checked
> the car before delivery to me simply put a modern 10W40 in it so that
> might explain a lot..
>
> My next question is about how much pre-ignition is allowed on our beloved
>  413 engine?
> When I checked the timing last weekend prior to bring the car for its
> final check to the local DMV, I noticed that is has a massive 16 degrees
> BTDC timing!!
> The FSM says that the timing should be 10 degrees BTDC but when I readjust
>  the timing to that amount I experienced a severe powerloss :( For the
> book "How to repair big block Mopar engines" by Don Taylor I learned that
> it is safe to start with 12 degrees BTDC and then check if the engines
> "pings".. Well, I have heard no pinging with even 16 degrees
> BTDC and the engine is running very smooth then (a lot smoother at idle
> then with 10 degrees BTDC timing) and has lots and lots of power. Trotlle
> response is very impressive with that kind of pre-ignition set.
>
> But will I be safe with 16 degrees BTDC ?? If memory serves me well the
> same Don Taylor also mentioned that you should never go beyond the limit
of
> +/- 4 degrees then the factory given 10 degrees of pre-ignition. That
> means that 14 degrees BTDC should be the limit for my engine?
>
> What is your advice on both subjects??
>
>
> Many thanks for your thoughts!
>
>
>
> Robert
>
>
>
>
> -----------------  http://www.imperialclub.com  -----------------
> This message was sent to you by the Imperial Mailing List. Please
> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
> with everyone. Private messages (and attachments) for the Administrators
> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
> http://imperialclub.com/unsubscribe.htm
>
>
>
>
>
>
> -----------------  http://www.imperialclub.com  -----------------
> This message was sent to you by the Imperial Mailing List. Please
> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
> with everyone. Private messages (and attachments) for the Administrators
> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
> http://imperialclub.com/unsubscribe.htm
>
>
>




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please 
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be 
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm





-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.