Re: [Chrysler300] 300H Fuel problem - answer

[GERALD OLSON <olson77@xxxx>]

Miller Special Tools -- 800-801-5420---tool #3053 is $71 plus shipping 
and its on back order till 1st week of July. Ain't it fun trying to do 
an engine right? regards, Jerry



----- Original Message -----
From: Robert Merritt <okbobwynmer@xxxx>
Date: Friday, May 30, 2003 11:46 am
Subject: Re: [Chrysler300] 300H Fuel problem - answer

> Bill,
> The downside to not using the burnishing tool is that
> as it is being retracted, as well as burnishing, it
> also slightly expands the bushing to make it fit the
> block. Without burnishing, the bushing could be
> tighter on the shaft and too loose in the block,
> letting it turn and wear the block. 
> It may be a while before I can even try to find my
> burnishing tool. I am a wheat farmer and harvest
> starts in a few days and I don't have my combine
> ready, so my car hobby will be on the back burner till
> after harvest. Check with me in about a month if you
> haven't found one by then.
> --- William Huff <wbh@xxxx> wrote:
> > Thanks Bob,
> > 
> > I would surely be interested in buying or renting
> > one. Please let me know 
> > what you find.
> > 
> > Thanks,
> > 
> > Bill
> > 
> > 29 May 2003 18:55:52 -0700 (PDT)
> > Date: Thu, 29 May 2003 18:55:52 -0700 (PDT)
> > From: Robert Merritt <okbobwynmer@xxxx>
> > Subject: Re: [Chrysler300] 300H Fuel problem -
> > answer
> > 
> > To: William Huff <whuff@xxxx>
> > Cc: chrysler300@xxxxxxxxxxxxxxx
> > 
> > 
> > Bill,
> > Over the years I have bought the specialty tools
> > from
> > several dealerships that had gone out of business.Of
> > course a lot of the popular tools were missing but
> > it
> > is amazing how many of the kits received in the
> > later
> > years just before they went out hadn't even been
> > opened.
> > I haven't built an engine recently so I don't know
> > for
> > sure where it is but will look thru my building and
> > see if I have duplicates. If I can find it I may be
> > able to duplicate it with my lathe, or at least
> > furnish exact measurements so other club members
> > could
> > make their own.
> > Okie Bob
> > --- William Huff <whuff@xxxx> wrote:
> > > Bob,
> > >
> > > I have done this also, but I never burnished the
> > > bearing since I don't have
> > > a burnishing tool. What did you use to burnish
> > the
> > > bearing, and is there
> > > any down side to not doing the burnishing?
> > >
> > > Bill Huff
> > >
> > >
> > >
> > > I pull the
> > > distributor, and check for excessive side play in
> > > the
> > > shaft and pull it out and see if the shaft shows
> > > wear
> > > just below the gear and if so, replace the shaft
> > at
> > > the same time the bushing is replaced and
> > burnished.
> > >
> > >
> > 
> > __________________________________
> > Do you Yahoo!?
> > Yahoo! Calendar - Free online calendar with sync to 
> > Outlook(TM).http://calendar.yahoo.com
> > 
> 
> 
> __________________________________
> Do you Yahoo!?
> Yahoo! Calendar - Free online calendar with sync to Outlook(TM).
> http://calendar.yahoo.com
> 
> ------------------------ Yahoo! Groups Sponsor --------------------
> -~-->
> Get a FREE REFINANCE QUOTE - click here!
> http://us.click.yahoo.com/2CXtTB/ca0FAA/ySSFAA/8LmulB/TM
> -------------------------------------------------------------------
> --~->
> 
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
> 
> For list server instructions, go to 
> http://www.chrysler300club.com/yahoolist/inst.htm 
> 
> To unsubscribe from this group, send an email to:
> Chrysler300-unsubscribe@xxxxxxxxxxxxxxx
> 
> 
> 
> Your use of Yahoo! Groups is subject to 
> http://docs.yahoo.com/info/terms/ 
> 
> 
>