Re: [Chrysler300] Spark plug wires.
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Spark plug wires.



Marshall and All:
Wire routing on the "G" (F is mostly the same) is quite the  arrangement!
 
1. Wires #1 and #3 go thru the four way bracket attached to the left front  
intake manifold bolt, over
the left valve cover, thru the 2-way wire bracket which is secured to  the 
lower front valve cover
attachment nut and then to their respective spark plugs.  Note: #3  nipple is 
an obtuse angle
to provide dipstick clearance.  All others are right angle and a  
reddish-brown color.  Distributor
end nipples are all straight and black except for #1 which is  red.
2.  Wires #5 and #7 also go thru the 4-way bracket, then turn rearward  and 
pass under the ram tubes, 
thru the two 2-way long narrow brackets secured by the intake manifold  bolts 
(left side of engine).  
They then curl around  the rear of  the head and  pass thru the 2-way bracket 
attached to the left rear 
head bolt.  #8 of course is then attached to its nearby spark  plug, while #5 
continues on forward to its plug.
3.  Wires #2, #4, and #6 go from the distributor right and down to the  4-way 
bracket secured by the 
right front head bolt.  From there, they go rearward to their  respective 
spark plugs.  On some "Gs"
there is a wire bracket near the #6 spark plug secured with a head  bolt.
4. FINALLY (!) #8 plug wire goes from the distributor rearward under the  ram 
manifold and thru the TWO 
long 2-way brackets attached to the manifold bolts (right side of  engine).  
It then curls down and thru the 
2-way small bracket attached with the right rear head bolt and on to  its 
nearby spark plug.
Whew!  Hope this is just a little clearer than mud, and helps out a  bit.  
Hope it also looks ok when it is        on the listserver.
300ly, Gil C.
    
 
 
In a message dated 7/16/2008 12:14:15 P.M. Eastern Daylight Time,  
yelof@xxxxxxxx writes:

I am  assembling my 61 300G engine and need to know the routing of the
plug  wires.  Below the heads and exhaust manifolds, over the valve
covers,  or some of each?  Detailed pictures would be great.  Thanks  in
advance.

Minnesota  Marshall

------------------------------------

To send a message  to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For  list server instructions, go to  
http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to  http://www.forwardlook.net/300-archive/Yahoo! Groups Links








**************Get the scoop on last night's hottest shows and the live music 
scene in your area - Check out TourTracker.com!      
(http://www.tourtracker.com?NCID=aolmus00050000000112)


[Non-text portions of this message have been removed]


------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.