Re: [Chrysler300] electric window motor removal ?

["Fern" <crc@xxxxxxxxxxxxxxx>]

Hi Jeff:

      Before removing the window, make sure that the switch is in fact working. So by-pass the switch assembly by feeding 12 volts power directly to the motor by simply unplugging the plug near the motor and feeding the power directly in there. You may have to reverse your feed wires to get the motor to go in the right direction. I doubt very much that the motor is burnt. You could also check with a volt meter to make sure that +12 volts is in fact reaching the motor feed. Fern



  ----- Original Message ----- 
  From: JJ 
  To: Fern ; Chrysler300@xxxxxxxxxxxxxxx ; Rich Barber 
  Sent: Sunday, March 22, 2009 2:25 AM
  Subject: Re: [Chrysler300] electric window motor removal ?


  Thanks Rich and Fern, I was running my finger along the crank arm and felt all those teeth so im assuming its that which would have severed me pinky? I had both bolts loose today and something told me to stop and ask the question on the 300 forum first - LUCKY indeed!
  Ill try and find some literature on how to do it correctly first.
  The window is in the down position so im assuming this is the danger zone?
  Jeff
  ----- Original Message ----- 
  From: Fern 
  To: 'lil_jake5' ; Chrysler300@xxxxxxxxxxxxxxx ; Rich Barber 
  Sent: Sunday, March 22, 2009 5:57 PM
  Subject: Re: [Chrysler300] electric window motor removal ?

  It's a very dangerous procedure so wear gloves to protect your valuable fingers. Fern

  ----- Original Message ----- 
  From: Rich Barber 
  To: 'lil_jake5' ; Chrysler300@xxxxxxxxxxxxxxx 
  Sent: Saturday, March 21, 2009 11:40 PM
  Subject: RE: [Chrysler300] electric window motor removal ?

  Jeff:

  Be sure to wait until you receive or obtain proper guidance on this job. It
  seems I have read that the stored energy in window regulator springs can
  remove or damage important parts of your body.

  C-300'ly,
  Rich Barber
  1955 C-300 (Long window cranks in front, shorter ones in back)

  -----Original Message-----
  From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
  Behalf Of lil_jake5
  Sent: Saturday, March 21, 2009 9:40 PM
  To: Chrysler300@xxxxxxxxxxxxxxx
  Subject: [Chrysler300] electric window motor removal ?

  Hi all,
  Was on a run last night and my electric motor in the window winder has burnt
  out and i have taken the door lining off and all handles etc, but my
  question is - is there an easy way of removing the motor and is it just 2
  bolts and it comes out.
  Its for a 1965 300L drivers side door window with the 4 window controler.
  The controller works the other 3 windows but not the drivers side(i think it
  got stuck in the down motion for a few hours and just burnt the motor or
  wiring out.
  any help apreciated by those who have done this exact job previouosly.
  I just want to be sure before i tackle it and stuff something up.
  cheers
  Jeff
  Australia

  ------------------------------------

  To send a message to this group, send an email to:
  Chrysler300@xxxxxxxxxxxxxxx

  For list server instructions, go to
  http://www.chrysler300club.com/yahoolist/inst.htm

  For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups
  Links

  ----------------------------------------------------------

  No virus found in this incoming message.
  Checked by AVG - www.avg.com 
  Version: 8.5.278 / Virus Database: 270.11.23/2016 - Release Date: 03/21/09 17:58:00

  ----------------------------------------------------------

  No virus found in this incoming message.
  Checked by AVG - www.avg.com 
  Version: 8.0.237 / Virus Database: 270.11.16/2005 - Release Date: 03/16/09 19:01:00

  [Non-text portions of this message have been removed]


  


------------------------------------------------------------------------------



  No virus found in this incoming message.
  Checked by AVG - www.avg.com 
  Version: 8.5.278 / Virus Database: 270.11.23/2016 - Release Date: 03/21/09 17:58:00


[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/