RE: [Chrysler300] '63 Chrysler 300 Torqueflight rebuild
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Chrysler300] '63 Chrysler 300 Torqueflight rebuild



Having just bought a 1964 Chrysler 300K convertible, I’m beginning the learning process.  Were some of the K’s equipped with aluminum TorqueFlites and some with cast iron?  Were there some different parts in the two different cases?  Were there different parts in the K trannys and other Chrysler trannys that year?  I think someone indicated more clutches in the K trannys.

 

I haven’t received the car yet, but know I will need a front header bar for the top mechanism and all interior panels in black.  Another question:  Was there a leather interior option or was leather interior  (seats only?) standard?  Are the side panels always vinyl?

 

I’ll have to sell our white ’55 C-300 after I complete the mechanical restoration of the Krag.   VIN of Krag:  8443149233  VIN of C-300:  3N551198.  

 

300-C-K’ly,

Rich Barber

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of retromobilia@xxxxxxxxxxx
Sent: Monday, June 20, 2011 10:55 AM
To: Dave Schwandt
Cc: chrysler300@xxxxxxxxxxxxxxx
Subject: Re: [Chrysler300] '63 Chrysler 300 Torqueflight rebuild

 

  

I know by experience on the manual aluminum case transmission there is a very serious problem after the first rebuild ; In that the case becomes warped for some reason and the shift can jump out of gear especially from first to second where the most torque is applied. It was found that bushings did not help and there was no apparent way to realign the case. 
Could this perhaps happen in the automatic as well. We were never certain if it was normal ware or some fault in the remanufacture process. 
Comments would be appreciated. 

J D Jung 
Retromobilia.net 

----- Original Message ----- 
From: "Dave Schwandt" <finsruskw@xxxxxxxxxxxxxxx <mailto:finsruskw%40iowatelecom.net> > 
To: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com> , "Mark Lindahl" <mplindahl@xxxxxxxxxxxxx <mailto:mplindahl%40sbcglobal.net> > 
Sent: Sunday, June 19, 2011 5:07:31 PM 
Subject: Re: [Chrysler300] '63 Chrysler 300 Torqueflight rebuild 

Mark, 
Was it built back to 300 specs with the correct # of clutch discs etc.? 

Sounds like an adjustment issue also. 
Check the kick-down and wide open throttle (WOT) and the cable adjustment 

Dave Schwandt 
----- Original Message ----- 
From: "Mark Lindahl" < mplindahl@xxxxxxxxxxxxx <mailto:mplindahl%40sbcglobal.net>  > 
To: < Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>  > 
Sent: Sunday, June 19, 2011 6:29 PM 
Subject: [Chrysler300] '63 Chrysler 300 Torqueflight rebuild 

Hi All, 

After a recent rebuild of an aluminum '63 torqueflight, I noticed the 
following changes. 

1) When reving the engine in neutral (with the park lock off) the vehicle 
moves forward slightly. When reving the engine, the transmission seems like 
it is only engaged about 10%. When reving the engine for about 10 seconds, 
the car moves about 4 feet. 
Is this a cable adjustment issue, rebuild issue, or non-issue? 

2) The trans does not chirp between 1st and 2nd gear under full throttle 
like it used to before the rebuild. The shift between 1st and 2nd is not a 
hard shift like it used to be. They convinced me to rebuild the trans 
although it seemed to shift pretty well. It had been 21 years since the last 
rebuild, but only about 35000 miles. 
Could this be a throttle linkage issue or something else, or non-issue? 

All other aspects of the trans seems to be fine. 

Thanks in advance for your comments. 
Regards, 
Mark Lindahl 
'63 300 Conv. 

[Non-text portions of this message have been removed] 

------------------------------------ 

To send a message to this group, send an email to: 
Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>  

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx <mailto:bob%40simplexco.com>  or 
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the 
"Leave Group" button 

For list server instructions, go to 
http://www.chrysler300club.com/yahoolist/inst.htm 

For archives go to 
http://www.forwardlook.net/300-archive/search.htm#querylangYahoo ! Groups 
Links 

[Non-text portions of this message have been removed]





[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylangYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.